Panasonic PT-D5700UL Mail setup page Continuing, An error is detected by self- diagnosis

Page 46

Using Web Browser Control

E-mail setup page (Continuing)

Enter the E-mail address of your desired recipient.

Select the conditions for sending E-mail.

ERROR:

an error is detected by self- diagnosis.

LAMP RUNTIME:

remaining lamp service time has reached the value set in the field.

INPUT AIR TEMPERATURE:

intake air temperature has reached the value set in the field.

Periodic warning interval setting (E-mail is sent on the checked days of the week/times)

Enter the E-mail address to which the E-mail is to be sent when two E-mail addresses are going to be used. Do not enter it when the second E-mail address is not going to be used.

Check these boxes when E-mail is to be sent periodically to two E-mail addresses. E-mail will be sent at the times and on the days checked.

Button to update settings

Select the conditions for sending the second E-mail. ERROR: an error is detected by self-diagnosis.

LAMP RUNTIME: remaining lamp service time has reached the value set in the field.

INPUT AIR TEMPERATURE: intake air temperature has reached the value set in the field.

Note • Only alphanumeric characters, “.”, “_”, “-”, or “@” are available to set an E-mail address.

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Commercial Use Model No. PT-D5700UModel number PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100UL Dear Panasonic CustomerSerial number PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100UL Contents Precautions with regard to safety Do not disassemble the lamp unit Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Always disconnect all cables before moving the projectorDo not place the projector in extremely hot locations AccessoriesDo not use the old lamp unit Electric shocks can result if this is not donePrecautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Effective range of remote control operation Using the remote control unitLoading dry cells Setting projector ID number to remote control Connect to the projector to use with a cableInstallation geometry InstallationProjection schemes Projection distance by projection lens PT-D5700U, PT-D5700UL Screen aspect ratioInstallation PT-DW5100U, PT-DW5100UL Screen aspect ratioPT-DW5100U, PT-DW5100UL Screen aspect ratio ET-DLE100 ET-DLE200 ET-DLE310 ET-DLE410Calculation formulas for projection distance by lens types Connection Setup precautionsPin assignments on the RGB2 input terminal are as follows Example of connecting with AV products Example of connecting with PCsPress the I button. on the main unit or the remote control Powering up the projectorMaking adjustment and selection When operating at the projector, please refer toPowering off the projector Direct power off functionHow to adjust the FOCUS, Zoom and Shift How to adjust the lensHow to remove the projection lens Status function Automatic adjustmentPress the Status button on the remote control Press the Shutter button againFor S-Video/Video/YPBPRsignals For RGB signalsFor DVI signals On-screen menusBasic menu operations Menu items settingResetting to the factory default Returning to the previousAdjusting the picture Adjusting the position Keystone Clock PhaseZoom Digital Cinema RealityClamp Position Input ResolutionEdge Blending Press to select an item, and press to adjust the setting XGA ModeSxga Mode Raster PositionColor Matching OPTION1 settingsPress the Enter button Press to adjust the values Press to select R, G, B and WhColor Correction Contrast ModeAuto Signal Back ColorFUNC1 DVI Signal LevelDVI Edid OSD PositionProjector ID OPTION2 settingsInstallation AltitudeLamp Relay Lamp PowerLamp Select RS-232CSystem Information Auto Power OFFPassword Cycle of displayed internal test patternsSystem requirements Setting the networkConnecting the PC Connection examplePassword change Using Web Browser ControlAccessing from the Web browser Click Change passwordBasic control Change password buttonDetail control Monitor information Error informationOK Normal operation Failed Occurrence of trouble Mail set up When Failed has appeared for an item Parameter DescriptionMail setup page Continuing An error is detected by self- diagnosisChange the authentication method as desired Authentication server set upDNS server set up Ping testContents of mail sent Adjust clockNetwork config Network statusPJLink security authentication Using the PJLink protocolSupported commands Command Control Description RemarksDisplay Setting Setting the securityPassword Change Control Device SetupCommunication conditions Factory setting Using the serial terminalsPin assignments and signal names Examples of connectionConnecting to a PC Computer Projector DTE specifications Control commandsCable specifications Pin assignments and controlIndication of lamp monitor Clean the air filter Cleaning and replacement of air filterProcedure of cleaning Dismantle the air filterLamp When to replace the Lamp unitReplacing the lamp unit AfterLamp unit will be hot after it has been used Lamp unit replacement stepsRemove the two screws securing the fan unit Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedureNo image Power doesNot turn on Image is blurredSpecifications PT-D5700U PT-D5700UL PT-DW5100URemote control Power source Length of power cord CabinetOutside dimensions Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMInstallation dimensions diagram DimensionsUnit mm, inch Trademark Acknowledgement Concernant LA Sécurité Ne jamais tenter de modifier ou de démonter le projecteur Précautions concernant la sécuritéNe pas surcharger la prise de courant Ne pas mettre d’objets étrangers dans le projecteurIl y a risque d’électrocution Pendant un orage, ne pas toucher le projecteur ou le câbleNe jamais démonter la lampe Il y a risque d’électrocution ou d’explosionSinon cela peut causer des chocs électriques Ne pas empêcher la chaleur de s’échapperNe pas utiliser la lampe usée Le bloc lampe risquerait de se casserMise au rebut Nettoyage et maintenancePrécautions pour la manipulation Précautions pour l’utilisationAprès Remplacement de la lampeMoment adéquat pour remplacer la lampe Heures*2Préparez un tournevis Phillips à l’avance Procédure de remplacement de la lampeLa lampe est chaude si elle vient d’être utilisée Poignée LampePhone FAX Mail projectorsupport@us.panasonic.com Panasonic Projector Systems CompanyTechnical Support Panasonic Canada Inc

PT-DW5100U, PT-D5700U, DW5100UL, PT-D5700UL specifications

Panasonic, a leader in innovative projection technology, offers a range of high-performance projectors including the PT-D5700UL, DW5100UL, PT-D5700U, and PT-DW5100U. These models are designed for environments that require high brightness, excellent color accuracy, and advanced features for seamless integration into various applications.

The PT-D5700UL and PT-D5700U are renowned for their high brightness of up to 7,000 lumens, making them ideal for large venues such as auditoriums, conference rooms, and outdoor events. They utilize a dual-lamp system, which not only enhances brightness but also provides reliability and longevity. The unique Dual Lamp Drive system ensures that if one lamp fails, the other continues to function, minimizing downtime and maintenance concerns.

Both projectors feature a WUXGA resolution of 1920 x 1200, providing sharp, detailed images that are essential for professional presentations. Their RGB booster technology enhances color reproduction, delivering vivid and realistic colors that captivate audiences. Additionally, these models feature a contrast ratio of up to 20,000:1, allowing presentations to have deep blacks and bright highlights, critical for effective visual storytelling.

On the other hand, the DW5100UL and PT-DW5100U models are specifically tailored for applications requiring exceptional brightness and excellent color fidelity, boasting a brightness of 5,000 lumens. They offer WXGA resolution (1280 x 800), making them suitable for a wide variety of display needs in corporate, educational, and entertainment settings. The incorporation of Panasonic’s Daylight View technology significantly enhances visibility even in brightly lit environments.

All four projectors are equipped with advanced connectivity options, including HDMI, DisplayPort, and LAN, allowing for easy integration into existing AV systems. They are also compatible with Crestron and AMX control systems, making them a flexible choice for complex installations.

Furthermore, the projectors utilize Panasonic's proprietary Solid Shine laser technology, which ensures consistent brightness and color quality over time while reducing maintenance requirements. With IP6X-rated dust-proof design and a cooling system that minimizes dust accumulation, users can rely on these projectors to perform optimally in challenging conditions.

In summary, Panasonic’s PT-D5700UL, DW5100UL, PT-D5700U, and PT-DW5100U projectors are engineered to deliver outstanding performance, durability, and versatility. They set a high standard for professional projection systems, equipped with cutting-edge technologies that ensure exceptional visual quality whether for business, education, or entertainment purposes.
Top Page Image Contents