Sharp LC-52HD1E, LC-46HD1E operation manual Initial installation wizard, Buttons to be used a/b/c/d

Initial installation

Initial installation wizard

When the TV powers on for the first time after purchase, the initial auto installation wizard appears. Follow the menus and make the necessary settings one after another.

Initial installation -> Language

Proceed

NOTE

•You can repeat this installation process by conducting the “Repeat initial installation” command. Press INFO, the option is located in the third line from the top.

Buttons to be used: a/b/c/d:

Move the cursor and select the settings.

OK:

Press to confirm and proceed to the next step.

YELLOW:

In some screens you can select or deselect items with YELLOW. When an item is selected, it is marked with ✔.

Initial installation -> Connect antenna cable(s)

Antenna cable(s) for:	to antenna socket(s):
Antenna/cable (analogue)
DVB-T
DVB-C
DVB-S (cable 1)
DVB-S (cable 2)

BACK:

Press to go back one step.

END:

If this icon is visible, you can exit the wizard.

Table of setting options in initial installation wizard

There are numerous settings in the initial installation wizard. When in doubt, refer to the table below so you don’t get overwhelmed.

Items	Explanation
Language	Select the language.
	Antenna/cable (analogue): analogue stations
Connect	via cable/antenna
	DVB-T:digital, terrestrial stations
antenna
	DVB-C:digital stations via cable
cable(s)
	DVB-S (cable 1): digital stations via satellite
	DVB-S (cable 2): digital stations via satellite
Antenna DVB-T	If you are using an active antenna, then select
	yes (5V) for the antenna power supply.

Items	Explanation
	The conventional settings will be derived from
	the selection of set location. Only change this
	if you know other symbol rates and modulation
Antenna	types or if you have to specify the network ID for
	your cable network (information available from
DVB-C
	your cable network provider). If you want to run
	the station search independently of the channel
	grid, select frequency search for the search
	method.
	Select which satellite(s) you receive from a list.
Antenna	For more than one satellite, select the type of
	your changeover switch or communal satellite
DVB-S
	system additionally. Ask your dealer in this
	regard.
	Specify here whether the high band of the
High band	selected satellite is to be searched in addition to
	the low band.
	Normally, you do not need to change the values
LNB	for high and low band, unless the LNC (LNB) of
	your satellite system uses a different oscillator
frequencies
	frequency (important for the frequency display).
Low Band/High
	After you have made these settings, you should
Band
	receive the picture and sound of the selected
	satellites (only with Astra1 and HOTBIRD).
	The symbol rates are specified by the satellite
Symbol rates	provider and do not normally need to be
	changed.
	Select the signal source from a list, the station
	of which is to be at the top of your station list
Favoured signal	(starting with station slot 1).
	• If you want to use the AV Link function with an
source	externally connected recorder, the analogue
	stations have to be between station slot 1 and
	99.
	Start the automatic station search with OK. First
	TV stations, then radio stations are searched
	for. The stations found in the automatic search
	are divided into the appropriate station blocks
	depending on the previously selected antenna
	cables (signal sources). Subsequently the
Start search	stations can only be re-sorted within these
	blocks. At the beginning of the station list
	you will find the block with the stations of the
	preferred signal source.
	Any mixed sorting of stations from different
	signal sources is only possible with the
	favourites list.
	In conclusion the connection wizard will start;
	with their help you can register and set your
	video devices or decoders, and connect them to
Connecting	the TV set. DVD players and DVD recorders are
additional	already registered at the factory.
devices	You can start the connection wizard manually
	later and add new devices. Further information
	is available on page 15 (Connection wizard) and
	page 22 (Speaker/amplifier connection).
Room antenna	With good reception conditions a room antenna
	can be used for DVB-T (socket ANT2).
	Under less favorable reception conditions, it is
	advisable to use an active antenna which has to
Active antenna	be set accordingly in the initial installation or in
	the “TV Menu > Connections > Antenna DVB >
	Antenna DVB-T”. (See “Antenna DVB-T” on this
	page).
Unidirectional	If the location is outside of the normal
	transmission range then a directional antenna
antenna
	can be used to improve reception quality.

10