Sony SLV-AV100UX Press ON/STANDBY to turn on the unit, Press RF Channel on the unit

Page 13

Step 6 Tuning your TV to the unit’s VCR

If you connected the unit to your TV using a EURO-AV cable, skip this step.

ON/STANDBY

PROGRAM +/–

RF CHANNEL

1

ON/STANDBY

Press ON/STANDBY to turn on the unit.

2		Press RF CHANNEL on the unit.
		The factory-preset RF channel appears in the display
	RF
		window.
	CHANNEL
		The unit’s VCR signal is output through this channel to the

		TV.

RF

3	Turn on your TV and select a programme position
	for the unit’s VCR picture.

Getting Started

4	Tune the TV’s programme position to the RF
	channel shown in the display window so the

picture on the right appears on the TV screen.

Refer to your TV manual for tuning instructions.

If the picture does not appear clearly, see “To obtain a clear picture from the unit’s VCR” below.

SONY VIDEO CASSETTE RECORDER

5	Press RF CHANNEL.

You have now tuned your TV to the unit’s VCR. Whenever

RF

CHANNELyou want to play a video tape, set the TV to this programme position. This programme position will now be referred to

as the VCR’s programme position.

To check that the TV tuning is correct

Set the TV to the VCR’s programme position and press PROGRAM +/– on the unit. If the TV screen changes to a different programme each time you press PROGRAM +/–, the TV tuning is correct.

To obtain a clear picture from the unit’s VCR

If the picture does not appear clearly in step 4 above, press PROGRAM +/– in step 4, to select another RF channel. Then tune the TV’s programme position to the new RF channel until a clear picture appears.

Getting Started

13

Image 13

Contents Amplifier Integrated Video Cassette Recorder Safety PrecautionsInstalling Compatible colour systemsTable of contents Step Inserting the batteries Using the remote commanderGetting Started Unit and the EURO-AV Scart connector On the TV Aerial input on your TV usingBefore you connect Disconnect the aerial cable from yourIf your TV doesn’t have a EURO-AV Scart connector Connecting speaker systems Listening through the headphones Connecting an active wooferSpeakers Rear L/R connectors Placing the speakers Connecting various audio/video equipment Connect the mains lead to the mains Supplied Conserving power while the unit is standing byPress ON/STANDBY to turn on the unit To check that the TV tuning is correctPress RF Channel on the unit Turn on your TV and select a programme positionPress VHS Tuner to turn on the unit and TV Press Easy SET UP on the unitSet the TV for VCR reception Preset automatically, change the programme Lift the top cover of the remote commanderPositions of the stations, and disable the unused Programme positions. If all the settings arePress ?// to select the centre mode Setting up the unit with Easy SET UPHave an equal volume balance with the other Decrease the volume of the centre speaker so youVolume of the rear speakers so you have an Equal volume balance with the other speakers atIf you have only front and centre speakers If you have only front and rear speakersBefore you start… Manual setup Presetting channelsManual setup Presetting channels If the picture is not clear Disabling unwanted programme positionsManual setup Selecting station names/setting up Video Plus+ Press Cursor / to highlight the guide channel column only Guide Station name Channel Setting up Video Plus+ for satellite broadcasts Changing programme positions Manual setup -- Changing/disabling programme positionsITV BBC1 BBC2 CH4 Select Manual setup -- Changing/ disabling programme positions Setting the clock manually Manual setup Setting the clockManual setup Setting the clock Changing the station for Auto Clock Set Basic VCR Operations Playing a video tapeTo change the information in the display window To use the time counterTo mute the sound Fields Using the pre- programmed soundPress r REC to start recording To stop recording Recording TV programmesTo check the remaining tape length To watch another TV programme while recordingTo save a recording Recording TV programmesRecording TV programmes using Video Plus+ To record satellite broadcasts Recording TV programmes using Video Plus+Using the unit after setting the timer Setting the timer manually Press Cursor / to confirm the setting Timer recording with PDC signalsPress Execute Press Timer REC ON/OFF Daily/weekly recordingChecking/changing/ cancelling timer settings When the timer settings overlap Audio/Video Equipment Operations Selecting the equipmentControlling the function buttons Before operating audio/video equipment Watching a picture while listening to audio equipmentFunction buttons on the unit Function To turn off the whole system To increase or decrease the volumeControlling VCRs Controlling VCRs which have the Command Mode selectorTurning on and controlling the unit’s VCR To relate VIDEO1 or VIDEO2 with Command Mode again Using the remote commander buttons to control the other VCRControlling VCRs Turning on and controlling another VCR Turning off the selected VCRControlling the TV Turning off the TV Controlling the TV Using the TV independentlyTo select the TV’s input source To scan preset stations Listening to preset radio programmesTo scan the preset stations Listening to a radio programmeTo locate a track with the number buttons Playing back a CDPlaying a tape Controlling a cassette deckRecording on a tape Controlling a cassette deck Controlling a DAT deck Customizing the remote commander for a DAT deckControlling a DAT deck Controlling an MD deck Customizing the remote commander for an MD deckPlaying an MD Recording on an MD Controlling an MD deckControlling an LD player Customizing the remote commander for an LD playerPlaying back an LD To start playback from the beginning of either LD sideTurning off the LD player Controlling an LD playerSound Field Operations Taking advantage of the sound fieldsSelecting the sound field To temporarily turn off the sound effect you setWhat’s Dolby Surround and Dolby Pro Logic Surround? Taking advantage of the sound fieldsWhat’s surround sound? Getting the most out of Dolby Pro Logic Surround sound Adjusting the delay timeCustomizing the sound fields To start your adjustment from a flat equalizer curve Adjusting the tone for all sound fieldsTo return to the previous menu Press Cursor /. to move the cursor I to Tone EditSource, then repeat steps Start playing a programmeHighlight Effect Press EXECUTE, then press CursorReinforcing the bass sound for all sound fields Source, then repeat steps Through 4 in Using the preSound fields in step Reconfiguring the Prologic and Theatre sound fields Increasing the maximum rear speaker level Playing/searching at various speeds Using the Click Shuttle ringAdvanced VCR Operations To extend the duration Recording TV programmes using the quick timerNicam system Recording stereo and bilingual programmesTo select the sound while recording How sound is recorded on a video tape To stop searching Searching using the index functionAdjusting the tracking Adjusting the pictureAbout Optimum Picture Control OPC Menu choices Changing menu optionsEditing Recording from another VCR or LD playerBefore you start editing Before you start dubbing… Audio dubbingTo listen to both the hi-fi and normal audio To stop while editingTo restore the factory settings for VIDEO1 or VIDEO2 Customizing the remote commander function buttonsAdditional Information Factory set functionsSymptoms caused by contaminated video heads TroubleshootingTroubleshooting Remote commander does System Amplifier General SpecificationsVCR Inputs and outputs Front panel Index to parts and controlsFront panel, with cover opened Display window Rear panel Index to parts and controls Remote commander Remote commander, with top cover opened Y, Z Index