Sony SLV-AV100UX operating instructions Manual setup Presetting channels, Before you start…

Page 19

Manual setup — Presetting channels

If some channels could not be preset using EASY SET UP, you can preset them manually.

Before you start…

•Press VHS TUNER.

–If the TV doesn’t turn on, turn it on manually.

Press VHS TUNER again if connected with a EURO-AV (Scart) cable.

–If connected with a EURO-AV (Scart) cable, the TV is automatically set to VCR reception.

–If connected with only the antenna cable, set the TV to the VCR’s programme position manually.

Getting Started

MENU

1

EXECUTE

CURSOR

> / . / ? / /

PROG +/–

2

Lift the top cover of the remote commander.

Press MENU. Then press CURSOR >/. to move the cursor (I) to VHS MENU, and press EXECUTE.

VHS MENU

T I MER SET / CHECK

SET UP MENU

TUNER PRESET

SET UP CH & VIDEO Plus+

CLOCK SET

SELECT	:
SET	:	EXECUTE
EXIT	:	MENU

Press CURSOR >/. to move the cursor (I) to TUNER PRESET and press EXECUTE.

TUNER PRESET	PROG10

CHANNEL SET	2 1
AFT	ON	OFF
FINE TUNING

SELECT :

SET :

Note

•The menu disappears automatically if you don’t proceed within a few minutes.

3

4

Press CURSOR >/. to move the cursor (I) to CHANNEL SET.

TUNER PRESET	PROG10

CHANNEL SET	2 1
AFT	ON	OFF
FINE TUNING

SELECT :

SET :

Press PROG +/– to select the programme position.

Selected programme position

TUNER PRESET			PROG4
CHANNEL SET		2 1
AFT		ON	OFF
FINE TUNING
SELECT	:
SET	:

continued

Getting Started

19

Image 19

Contents Amplifier Integrated Video Cassette Recorder Compatible colour systems PrecautionsSafety InstallingTable of contents Step Inserting the batteries Using the remote commanderGetting Started Disconnect the aerial cable from your Aerial input on your TV usingUnit and the EURO-AV Scart connector On the TV Before you connectIf your TV doesn’t have a EURO-AV Scart connector Connecting speaker systems Placing the speakers Connecting an active wooferListening through the headphones Speakers Rear L/R connectorsConnecting various audio/video equipment Connect the mains lead to the mains Supplied Conserving power while the unit is standing byTurn on your TV and select a programme position To check that the TV tuning is correctPress ON/STANDBY to turn on the unit Press RF Channel on the unitPress VHS Tuner to turn on the unit and TV Press Easy SET UP on the unitSet the TV for VCR reception Programme positions. If all the settings are Lift the top cover of the remote commanderPreset automatically, change the programme Positions of the stations, and disable the unusedPress ?// to select the centre mode Setting up the unit with Easy SET UPEqual volume balance with the other speakers at Decrease the volume of the centre speaker so youHave an equal volume balance with the other Volume of the rear speakers so you have anIf you have only front and centre speakers If you have only front and rear speakersBefore you start… Manual setup Presetting channelsManual setup Presetting channels If the picture is not clear Disabling unwanted programme positionsManual setup Selecting station names/setting up Video Plus+ Press Cursor / to highlight the guide channel column only Guide Station name Channel Setting up Video Plus+ for satellite broadcasts Changing programme positions Manual setup -- Changing/disabling programme positionsITV BBC1 BBC2 CH4 Select Manual setup -- Changing/ disabling programme positions Setting the clock manually Manual setup Setting the clockManual setup Setting the clock Changing the station for Auto Clock Set Basic VCR Operations Playing a video tapeTo change the information in the display window To use the time counterTo mute the sound Fields Using the pre- programmed soundTo watch another TV programme while recording Recording TV programmesPress r REC to start recording To stop recording To check the remaining tape lengthTo save a recording Recording TV programmesRecording TV programmes using Video Plus+ To record satellite broadcasts Recording TV programmes using Video Plus+Using the unit after setting the timer Setting the timer manually Daily/weekly recording Timer recording with PDC signalsPress Cursor / to confirm the setting Press Execute Press Timer REC ON/OFFChecking/changing/ cancelling timer settings When the timer settings overlap Audio/Video Equipment Operations Selecting the equipmentControlling the function buttons Before operating audio/video equipment Watching a picture while listening to audio equipmentFunction buttons on the unit Function To turn off the whole system To increase or decrease the volumeControlling VCRs Controlling VCRs which have the Command Mode selectorTurning on and controlling the unit’s VCR Turning off the selected VCR Using the remote commander buttons to control the other VCRTo relate VIDEO1 or VIDEO2 with Command Mode again Controlling VCRs Turning on and controlling another VCRControlling the TV Turning off the TV Controlling the TV Using the TV independentlyTo select the TV’s input source Listening to a radio programme Listening to preset radio programmesTo scan preset stations To scan the preset stationsTo locate a track with the number buttons Playing back a CDPlaying a tape Controlling a cassette deckRecording on a tape Controlling a cassette deck Controlling a DAT deck Customizing the remote commander for a DAT deckControlling a DAT deck Controlling an MD deck Customizing the remote commander for an MD deckPlaying an MD Recording on an MD Controlling an MD deckTo start playback from the beginning of either LD side Customizing the remote commander for an LD playerControlling an LD player Playing back an LDTurning off the LD player Controlling an LD playerTo temporarily turn off the sound effect you set Taking advantage of the sound fieldsSound Field Operations Selecting the sound fieldWhat’s Dolby Surround and Dolby Pro Logic Surround? Taking advantage of the sound fieldsWhat’s surround sound? Getting the most out of Dolby Pro Logic Surround sound Adjusting the delay timeCustomizing the sound fields Press Cursor /. to move the cursor I to Tone Edit Adjusting the tone for all sound fieldsTo start your adjustment from a flat equalizer curve To return to the previous menuPress EXECUTE, then press Cursor Start playing a programmeSource, then repeat steps Highlight EffectReinforcing the bass sound for all sound fields Source, then repeat steps Through 4 in Using the preSound fields in step Reconfiguring the Prologic and Theatre sound fields Increasing the maximum rear speaker level Playing/searching at various speeds Using the Click Shuttle ringAdvanced VCR Operations To extend the duration Recording TV programmes using the quick timerNicam system Recording stereo and bilingual programmesTo select the sound while recording How sound is recorded on a video tape To stop searching Searching using the index functionAdjusting the tracking Adjusting the pictureAbout Optimum Picture Control OPC Menu choices Changing menu optionsEditing Recording from another VCR or LD playerBefore you start editing Before you start dubbing… Audio dubbingTo listen to both the hi-fi and normal audio To stop while editingFactory set functions Customizing the remote commander function buttonsTo restore the factory settings for VIDEO1 or VIDEO2 Additional InformationSymptoms caused by contaminated video heads TroubleshootingTroubleshooting Remote commander does System Amplifier General SpecificationsVCR Inputs and outputs Front panel Index to parts and controlsFront panel, with cover opened Display window Rear panel Index to parts and controls Remote commander Remote commander, with top cover opened Y, Z Index