INITIAL SETTINGS
Hint: Before starting initial setup you must connect antenna.
INITIAL SETTINGS
This section describes the initial settings when you first turn on the power after purchase. The initial setting items are shown below.
• LANGUAGE SELECTION
You can select the menu language displayed on the screen among English, Spanish and French.
•AUTOSCAN (TV/DTV)
(Select “Air” when using antenna)
The channels broadcasted in TV and DTV are automatically scanned and memorized. Only the receivable channels in the area where this TV is used will be memorized.
•AUTOSCAN (CATV)
(Select “Cable” when using RF/Incoming cable) The channels broadcasted in CATV are automati- cally scanned and memorized.
POWER | SLEEP | INPUT |
SELECT |
4Select destination of ANT IN jack using [K/L], press [ENTER].
InitialI i i l Setup
Make sure the antenna is connected to "ANT. IN" jack. | Air | ||
Select the destination of "ANT. IN" jack. |
| Cable | |
|
|
| |
Air |
|
|
|
Cable | Or |
|
|
| ANT IN |
|
|
Select | BACK | Back | SETUP |
ENTER Enter | Exit | ||
5Autoscan will start automatically.
InitialI i i l Setup
Now the system is scanning for channels,please wait.
5%
Analog channels | 1ch |
|
|
|
|
|
|
Digital channels | 0ch |
|
|
|
|
|
|
| SETUP | ||
Exit
FOR USE / INITIAL SETTINGS
1 | 2 | 3 |
4 | 5 | 6 |
|
| AUDIO |
7 | 8 | 9 |
|
| STILL |
- | 0 |
|
SETUP |
| SCREEN |
| MODE | |
|
| ENTER |
BACK |
| INFO |
1After making all the necessary connections, turn on this TV.
2Press [POWER]. Initial Setup menu will appear.
•This operation may take a few moments.
•If Initial Setup menu does not appear press and hold [ENTER] for 3 seconds, initial setup will appear then proceed to step 3. If you have already turned on this TV before, refer to “LANGUAGE SELECTION” on page 17 to select a language for the
3Select your language using [K/L], press [ENTER].
When you first turn on the power, the following screen is displayed.
InitialI i i l Setup
Select the language used for setup. | English | |
|
| Español |
Elija idioma de preparación. | ||
|
|
|
•When scanning is completed, the smallest memorized channel will be displayed.
NOTES:
•If you do not operate this TV for more than 45 seconds while initial setup, the message boxes start to move to the lower
•The initial Autoscan function can be executed for either “Air” or “Cable” only once. When you change the connection (Air/Cable), set the “Autoscan” again. (Refer to page 14.)
•If you connect cable system directly, contact the CATV installer.
•When the scanning is not completed, Helpful Hint will be displayed every time you turn on the power. If you have previously registered channels when this screen appears you can select a channel with number buttons.
No channel is registered.
Press and hold "ENTER" key for 3 seconds.
Contact support hotline provided on manual or back of unit.
Sin canal registrado.
Mantenga oprimida la tecla "ENTER" durante 3 segundos.
Llame teléfono de apoyo en manual o atrás de TV.
Pas de chaîne consign.
Maintenir la touche "ENTER" pressée 3 secondes.
Contacter numero d'urgence dans manuel ou arrière appareil.
•Support hotline is provided on the front page of this manual.
PREPARATION
Sélectionner langue écran config. | Français | |
Select | ENTER Enter | SETUP |
Exit | ||
The Antenna Confirmation will be displayed in the selected language after you press [ENTER].
13
EN