Sylvania 6900DTD owner manual Connections

Page 19

Connections

1Use a standard antenna cable to connect the wall jack to the ANT IN jack on STB.

2Use a standard audio cable to connect the audio output jacks (L, R) of STB to the audio input jacks (L, R) on the TV.

NOTE:

If your TV is monaural (MONO) and has only one audio jack, use a standard audio cable (white) to connect the audio output jack (white) on STB to the audio input jack (white) on the TV. The red cable and jack will not be used.

3Use a component video cable to connect the component video output jacks (Y/ Pb/ Pr) on STB to the component video input jacks (Y/ Pb/ Pr) on the TV.

4Set the video resolution selection switch to “1080i.”

NOTE:

For the capability of your TV and further information, refer to TV owner’s manual.

5After completing the connection to the TV, plug the AC power cord of the TV into the AC outlet, then turn the TV on.

6Set the TV to the input mode.

NOTE:

Refer to the TV owner’s manual for further information.

7Plug the AC power cord of STB into the AC outlet, then turn STB on.

19

EN

2 Connections

1A23

Image 19

Contents 6900DTD Table of Contents Important Safeguards S2 8 9 8 a Precautions Receives both Information on digital broadcastingAtsc and Ntsc Ntsc Major features of STBAtsc HdtvSetup button Power buttonPower indicator Remote control sensorRear Panel Remote Control Remote controller unit and AA batteries x2 Part No. NE120UD AccessoriesInstalling batteries Snap the battery cover backSetup Wizard Reference to Setup menuDisplay ChannelClock Detail Connections to antenna When Connecting to Cable BOX AlsoCable BOX Right Connections to other devices Connections Connections STB connection using S-VIDEO output to Sdtv Connections STB connection using Video output to Sdtv Stereo Component Connections STB connection to a standard stereo systemDigital Decoder Connections STB connection to a decoder with Dolby DigitalVCR Setup Wizard will appear Initial setupSetup Wizard 1/8 will appear To skip the scanning Setup Wizard 3/8 will appearButtons, then press Enter STB starts scanning channelsRefer to Information on Time Zones on Setup Wizard 5/8 will appearWhen not using the auto-clock setting Press Enter when the cursor is on SETSelect OFF on the channel map, then press Enter Press Enter 26-1Watching TV When using CH o/p buttonsSelecting a desired channel TV-Y When using number buttons E.g., entering 26-11800 1830 1900 1930 2000 Press Info to clear When tuning in a channel from NtscChannel banner Press Info to display a channel bannerLock DTVChoosing audio Language Audio map Only when tuning in AtscPress Audio button When tuning in NtscSequence will repeat as shown below when available When tuning in AtscDuring STILL, the programs audio will continue Picture StillPress Still o button while watching Press any button to quitRestricted Program No SignalOn screen messages ScanningEPG will appear on the screen Press EPG button while watching TVWhen going back to the previous Select the desired program using o / p Navigation buttonsWhen selecting a program being broadcast CC Closed Caption Components of Electronic Program Guide EPGSetup menu for preference ADD/ Delete Press Setup to display Setup menuWhen adding the digital channel Adding channelsChannel menu will appear Select Channel using o / p navigationButtons, then press Enter Number To add, first enter the digital channelTo continue adding Select ADD using o / p navigation buttons, then press EnterPress Setup to exit Setup menu Information on Channel MapTo delete the digital channel Deleting channelsYou can add and delete channels in the channel map DeleteCursor will move to the channel map To continue deleting Press Enter when the cursor is on the digital channelWill be indicated in the box at the top of the screen Digital channel number 26 will be deletedChannel 26-1 will be tuned Adjusting antennaWhen adjusting the digital channel AntennaAntenna menu will appear, then STB starts Adjust the antenna direction to get the best receptionReceiving the signal strength of the channel When adjusting other channels continuouslyAutoscan Receiving channelsSelect Next using s / B navigation buttons, then press Enter Verify the antenna connection, then complete To cancel Autoscan during scanningWhen no Signal appears on the screen Autoscan is completeScreen Ratio Selecting screen formatsDisplay menu will appear Screen ratio will be set Press Enter to exit Setup menuScreen ratio options will appear Screen ratio should be selected to fit your TV screenDisplay Mode 43 TV Display mode will be setInformation on 43 TV STBSidebar Letter BoxZoom FullClock menu will appear Setting the clockTime Zone setting menu will appear Daylight savings time setting menu will appearMountain AlaskaHawaii PacificCurrent time setting menu will appear Activated Your settings will be activated4,5,6 Select OFF from the channel-map, then press Enter Will become black on the channel mapChannel search completed. will be indicated Detail menu will appear Setting a new passwordChip / CC Quit Channel Display Clock Detail Your new password is stored Password setting menu will appearCHIP/CC menu will appear CHIP/CC Setting for V-CHIP/CCCHIP/CC password window will appear When choosing STBcontrols V-CHIP Ratings Enter your 4-digit passwordWhen choosing TVcontrols V-CHIP Ratings Press Setup to exit Setup menu Mpaa Rating Setting Mpaa ratingPress Setup to display Setup menu Mpaa rating setting menu will appear When you want to block all PG-13 movies TV Rating Setting TV ratingPress Setup to display Setup menu Information on TV ratings TV rating setting menu will appearQuit Channel CC Selection Selecting CC optionsEnter your 4-digit password Serve as the preferred data channels CC options menu will appearSelected CC option will be set Menu Language Choosing the screen languageLanguage menu will appear Then press EnterTroubleshooting With weak signal Symptom RemedyAudio problems when Using coaxial digitalGlossary and Acronyms SpecificationsMpaa DSTNota Ubicación de los controlesInstalación de las pilas AL Conectar EL Equipo a UNA Caja Para Cable Conexiones de antenaConexión del STB a un Sdtv utilizando la salida Video Configuración inicial Si no desea usar la función de ajuste automático de reloj NuméricosCuando el cursor se encuentre en SET, presione Enter Presione EnterLimited Warranty