Sylvania 6900DTD owner manual Rear Panel

Page 9

Before Using

REAR PANEL

1

2

3

4

5

6

8 7

1 Before Using

1ANT. IN Jack:

Use to connect an antenna to STB.

2DIGITAL AUDIO (COAXIAL) Jack:

Use to connect a decoder or an amplifier to STB with a digital coaxial cable.

NOTE:

You must use this jack and a Dolby® Digital receiver for Dolby® Digital 5.1 playback.

3AUDIO R/ L Jacks: (2 pairs)

Use to connect your TV, a stereo system or a VCR to STB with standard audio cables.

NOTE for audio output:

There will be both digital audio output and analog audio output during digital broadcast. There will be only analog audio output during analog broadcast. When you want digital audio output during digital broadcast, the digital audio (coaxial) jack must be used.

Refer to the page describing the connection to a decoder with Dolby® Digital.

4VIDEO Jack: (Composite)

Use to connect your TV or a VCR to STB with a standard video cable.

5S-VIDEO Jack:

Use to connect your TV to STB with an S-Video cable.

NOTE:

When you use an S-Video cable, a composite video cable (yellow) is not necessary.

6COMPONENT VIDEO Jacks (Y/ Pb/ Pr):

Use to connect your TV to STB with component video cables.

NOTE:

This connection is required to display a high definition broadcast. Y (green), Pb (blue), Pr (red)

7Resolution selection switch (1080i/ 480p/ 480i):

Use to select the STB video output resolution 1080i, 480p and 480i. The default setting is 480i.

8AC power cord:

Connect to AC outlet.

9

EN

1A23

Image 9

Contents 6900DTD Table of Contents Important Safeguards S2 8 9 8 a Precautions Information on digital broadcasting Receives bothAtsc and Ntsc Atsc Major features of STBHdtv NtscPower indicator Power buttonRemote control sensor Setup buttonRear Panel Remote Control Installing batteries AccessoriesSnap the battery cover back Remote controller unit and AA batteries x2 Part No. NE120UDSetup Wizard Reference to Setup menuDisplay ChannelClock Detail When Connecting to Cable BOX Also Connections to antennaCable BOX Right Connections to other devices Connections Connections STB connection using S-VIDEO output to Sdtv Connections STB connection using Video output to Sdtv Stereo Component Connections STB connection to a standard stereo systemDigital Decoder Connections STB connection to a decoder with Dolby DigitalVCR Initial setup Setup Wizard will appearSetup Wizard 1/8 will appear Buttons, then press Enter Setup Wizard 3/8 will appearSTB starts scanning channels To skip the scanningRefer to Information on Time Zones on Setup Wizard 5/8 will appearPress Enter when the cursor is on SET When not using the auto-clock settingSelect OFF on the channel map, then press Enter Press Enter 26-1When using CH o/p buttons Watching TVSelecting a desired channel TV-Y When using number buttons E.g., entering 26-11800 1830 1900 1930 2000 Channel banner When tuning in a channel from NtscPress Info to display a channel banner Press Info to clearLock DTVChoosing audio Language Audio map Only when tuning in AtscSequence will repeat as shown below when available When tuning in NtscWhen tuning in Atsc Press Audio buttonPress Still o button while watching Picture StillPress any button to quit During STILL, the programs audio will continueOn screen messages No SignalScanning Restricted ProgramEPG will appear on the screen Press EPG button while watching TVSelect the desired program using o / p Navigation buttons When going back to the previousWhen selecting a program being broadcast CC Closed Caption Components of Electronic Program Guide EPGSetup menu for preference When adding the digital channel Press Setup to display Setup menuAdding channels ADD/ DeleteButtons, then press Enter Number Select Channel using o / p navigationTo add, first enter the digital channel Channel menu will appearPress Setup to exit Setup menu Select ADD using o / p navigation buttons, then press EnterInformation on Channel Map To continue addingYou can add and delete channels in the channel map Deleting channelsDelete To delete the digital channelCursor will move to the channel map Will be indicated in the box at the top of the screen Press Enter when the cursor is on the digital channelDigital channel number 26 will be deleted To continue deletingWhen adjusting the digital channel Adjusting antennaAntenna Channel 26-1 will be tunedReceiving the signal strength of the channel Adjust the antenna direction to get the best receptionWhen adjusting other channels continuously Antenna menu will appear, then STB startsAutoscan Receiving channelsSelect Next using s / B navigation buttons, then press Enter When no Signal appears on the screen To cancel Autoscan during scanningAutoscan is complete Verify the antenna connection, then completeSelecting screen formats Screen RatioDisplay menu will appear Screen ratio options will appear Press Enter to exit Setup menuScreen ratio should be selected to fit your TV screen Screen ratio will be setDisplay Mode Information on 43 TV Display mode will be setSTB 43 TVZoom Letter BoxFull SidebarClock menu will appear Setting the clockTime Zone setting menu will appear Daylight savings time setting menu will appearHawaii AlaskaPacific MountainCurrent time setting menu will appear Activated Your settings will be activated4,5,6 Will become black on the channel map Select OFF from the channel-map, then press EnterChannel search completed. will be indicated Detail menu will appear Setting a new passwordChip / CC Quit Channel Display Clock Detail Password setting menu will appear Your new password is storedCHIP/CC menu will appear CHIP/CC Setting for V-CHIP/CCCHIP/CC password window will appear Enter your 4-digit password When choosing STBcontrols V-CHIP RatingsWhen choosing TVcontrols V-CHIP Ratings Press Setup to exit Setup menu Mpaa Rating Setting Mpaa ratingPress Setup to display Setup menu Mpaa rating setting menu will appear When you want to block all PG-13 movies TV Rating Setting TV ratingPress Setup to display Setup menu Information on TV ratings TV rating setting menu will appearQuit Channel CC Selection Selecting CC optionsEnter your 4-digit password CC options menu will appear Serve as the preferred data channelsSelected CC option will be set Menu Language Choosing the screen languageLanguage menu will appear Then press EnterTroubleshooting Audio problems when Symptom RemedyUsing coaxial digital With weak signalGlossary and Acronyms SpecificationsMpaa DSTNota Ubicación de los controlesInstalación de las pilas AL Conectar EL Equipo a UNA Caja Para Cable Conexiones de antenaConexión del STB a un Sdtv utilizando la salida Video Configuración inicial Cuando el cursor se encuentre en SET, presione Enter NuméricosPresione Enter Si no desea usar la función de ajuste automático de relojLimited Warranty