Sylvania 6900DTD Connections STB connection to a standard stereo system, Stereo Component

Page 22

Connections

STB connection to a standard stereo system

NOTE:

Component video cable and audio cable are not included.

Rear panel of STB

STEREO COMPONENT

Audio cable

To audio input jacks (L, R)

Component video cable

To component video input

jacks (Y/ Pb/ Pr)

1Use a standard antenna cable to connect the wall jack to the ANT. IN jack on STB.

2Use a standard audio cable to connect the audio output jacks (L, R) on STB to the audio input jacks (L, R) on the stereo.

3Connect STB and the TV with a video cable.

NOTE:

Refer to the pages describing the connection to TV.

4Set the video resolution selection switch to “1080i.”

NOTE:

For the capability of your TV and further information, refer to TV owner’s manual.

5Plug the AC power cord of the stereo into the AC outlet, then turn the stereo on.

6Set the stereo to the input mode to which you connected the audio from the STB.

NOTE:

Refer to the stereo owner's manual for further information.

7Plug the AC power cord of STB into the AC outlet, then turn STB on.

22

EN

1A23

Image 22

Contents 6900DTD Table of Contents Important Safeguards S2 8 9 8 a Precautions Receives both Information on digital broadcastingAtsc and Ntsc Hdtv Major features of STBAtsc NtscRemote control sensor Power buttonPower indicator Setup buttonRear Panel Remote Control Snap the battery cover back AccessoriesInstalling batteries Remote controller unit and AA batteries x2 Part No. NE120UDReference to Setup menu Setup WizardChannel DisplayClock Detail Connections to antenna When Connecting to Cable BOX AlsoCable BOX Right Connections to other devices Connections Connections STB connection using S-VIDEO output to Sdtv Connections STB connection using Video output to Sdtv Connections STB connection to a standard stereo system Stereo ComponentConnections STB connection to a decoder with Dolby Digital Digital DecoderVCR Setup Wizard will appear Initial setupSetup Wizard 1/8 will appear STB starts scanning channels Setup Wizard 3/8 will appearButtons, then press Enter To skip the scanningSetup Wizard 5/8 will appear Refer to Information on Time Zones onWhen not using the auto-clock setting Press Enter when the cursor is on SETSelect OFF on the channel map, then press Enter 26-1 Press EnterWatching TV When using CH o/p buttonsSelecting a desired channel When using number buttons E.g., entering 26-1 TV-Y1800 1830 1900 1930 2000 Press Info to display a channel banner When tuning in a channel from NtscChannel banner Press Info to clearDTV LockAudio map Only when tuning in Atsc Choosing audio LanguageWhen tuning in Atsc When tuning in NtscSequence will repeat as shown below when available Press Audio buttonPress any button to quit Picture StillPress Still o button while watching During STILL, the programs audio will continueScanning No SignalOn screen messages Restricted ProgramPress EPG button while watching TV EPG will appear on the screenWhen going back to the previous Select the desired program using o / p Navigation buttonsWhen selecting a program being broadcast Components of Electronic Program Guide EPG CC Closed CaptionSetup menu for preference Adding channels Press Setup to display Setup menuWhen adding the digital channel ADD/ DeleteTo add, first enter the digital channel Select Channel using o / p navigationButtons, then press Enter Number Channel menu will appearInformation on Channel Map Select ADD using o / p navigation buttons, then press EnterPress Setup to exit Setup menu To continue addingDelete Deleting channelsYou can add and delete channels in the channel map To delete the digital channelCursor will move to the channel map Digital channel number 26 will be deleted Press Enter when the cursor is on the digital channelWill be indicated in the box at the top of the screen To continue deletingAntenna Adjusting antennaWhen adjusting the digital channel Channel 26-1 will be tunedWhen adjusting other channels continuously Adjust the antenna direction to get the best receptionReceiving the signal strength of the channel Antenna menu will appear, then STB startsReceiving channels AutoscanSelect Next using s / B navigation buttons, then press Enter Autoscan is complete To cancel Autoscan during scanningWhen no Signal appears on the screen Verify the antenna connection, then completeScreen Ratio Selecting screen formatsDisplay menu will appear Screen ratio should be selected to fit your TV screen Press Enter to exit Setup menuScreen ratio options will appear Screen ratio will be setDisplay Mode STB Display mode will be setInformation on 43 TV 43 TVFull Letter BoxZoom SidebarSetting the clock Clock menu will appearDaylight savings time setting menu will appear Time Zone setting menu will appearPacific AlaskaHawaii MountainCurrent time setting menu will appear Your settings will be activated Activated4,5,6 Select OFF from the channel-map, then press Enter Will become black on the channel mapChannel search completed. will be indicated Setting a new password Detail menu will appearChip / CC Quit Channel Display Clock Detail Your new password is stored Password setting menu will appearCHIP/CC menu will appear Setting for V-CHIP/CC CHIP/CCCHIP/CC password window will appear When choosing STBcontrols V-CHIP Ratings Enter your 4-digit passwordWhen choosing TVcontrols V-CHIP Ratings Press Setup to exit Setup menu Setting Mpaa rating Mpaa RatingPress Setup to display Setup menu Mpaa rating setting menu will appear When you want to block all PG-13 movies Setting TV rating TV RatingPress Setup to display Setup menu TV rating setting menu will appear Information on TV ratingsQuit Channel Selecting CC options CC SelectionEnter your 4-digit password Serve as the preferred data channels CC options menu will appearSelected CC option will be set Choosing the screen language Menu LanguageThen press Enter Language menu will appearTroubleshooting Using coaxial digital Symptom RemedyAudio problems when With weak signalSpecifications Glossary and AcronymsDST MpaaUbicación de los controles NotaInstalación de las pilas Conexiones de antena AL Conectar EL Equipo a UNA Caja Para CableConexión del STB a un Sdtv utilizando la salida Video Configuración inicial Presione Enter NuméricosCuando el cursor se encuentre en SET, presione Enter Si no desea usar la función de ajuste automático de relojLimited Warranty