Sylvania 6900DTD owner manual TV rating setting menu will appear, Information on TV ratings

Page 79

Advanced Operation

4Enter your 4-digit password.

• “ * ” will appear for each digit.

5 Select TV RATING using o / p navigation buttons, then press ENTER.

•TV rating setting menu will appear.

V-CHIP / CC

V-CHIP / CC

QUIT

Set TV rating

FV V S L D

QUIT

CHANNEL

DISPLAY

CLOCK

DETAIL

Enter password.

CHANNEL

DISPLAY

CLOCK

DETAIL

TV-MA

TV-14

TV-PG

TV-G

TV-Y7 TV-Y

After the correct password is entered, V-CHIP/CC menu will appear.

V-CHIP / CC

INFORMATION on TV ratings

QUIT

CHANNEL

DISPLAY

CLOCK

DETAIL

V-CHIP / CC

MPAA RATING

TV RATING

CCSELECTION NEW PASSWORD

STB

OFF

Content labels

V-CHIP / CC
	Set TV rating
QUIT	FV	V	S	L	D	5 Advanced
	FV	V	S	L	D
CHANNEL	TV-MA				Operation
CHANNEL	TV-14
	TV-14
DISPLAY	TV-PG
	TV-G
CLOCK	TV-Y7
	TV-Y7
	TV-Y
DETAIL	TV-Y
DETAIL

Age-based category

Possible content labels

79

EN

1A23

Image 79

Contents 6900DTD Table of Contents Important Safeguards S2 8 9 8 a Precautions Receives both Information on digital broadcastingAtsc and Ntsc Ntsc Major features of STBAtsc HdtvSetup button Power buttonPower indicator Remote control sensorRear Panel Remote Control Remote controller unit and AA batteries x2 Part No. NE120UD AccessoriesInstalling batteries Snap the battery cover backSetup Wizard Reference to Setup menuDisplay ChannelClock Detail Connections to antenna When Connecting to Cable BOX AlsoCable BOX Right Connections to other devices Connections Connections STB connection using S-VIDEO output to Sdtv Connections STB connection using Video output to Sdtv Stereo Component Connections STB connection to a standard stereo systemDigital Decoder Connections STB connection to a decoder with Dolby DigitalVCR Setup Wizard will appear Initial setupSetup Wizard 1/8 will appear To skip the scanning Setup Wizard 3/8 will appearButtons, then press Enter STB starts scanning channelsRefer to Information on Time Zones on Setup Wizard 5/8 will appearWhen not using the auto-clock setting Press Enter when the cursor is on SETSelect OFF on the channel map, then press Enter Press Enter 26-1Watching TV When using CH o/p buttonsSelecting a desired channel TV-Y When using number buttons E.g., entering 26-11800 1830 1900 1930 2000 Press Info to clear When tuning in a channel from NtscChannel banner Press Info to display a channel bannerLock DTVChoosing audio Language Audio map Only when tuning in AtscPress Audio button When tuning in NtscSequence will repeat as shown below when available When tuning in AtscDuring STILL, the programs audio will continue Picture StillPress Still o button while watching Press any button to quitRestricted Program No SignalOn screen messages ScanningEPG will appear on the screen Press EPG button while watching TVWhen going back to the previous Select the desired program using o / p Navigation buttonsWhen selecting a program being broadcast CC Closed Caption Components of Electronic Program Guide EPGSetup menu for preference ADD/ Delete Press Setup to display Setup menuWhen adding the digital channel Adding channelsChannel menu will appear Select Channel using o / p navigationButtons, then press Enter Number To add, first enter the digital channelTo continue adding Select ADD using o / p navigation buttons, then press EnterPress Setup to exit Setup menu Information on Channel MapTo delete the digital channel Deleting channelsYou can add and delete channels in the channel map DeleteCursor will move to the channel map To continue deleting Press Enter when the cursor is on the digital channelWill be indicated in the box at the top of the screen Digital channel number 26 will be deletedChannel 26-1 will be tuned Adjusting antennaWhen adjusting the digital channel AntennaAntenna menu will appear, then STB starts Adjust the antenna direction to get the best receptionReceiving the signal strength of the channel When adjusting other channels continuouslyAutoscan Receiving channelsSelect Next using s / B navigation buttons, then press Enter Verify the antenna connection, then complete To cancel Autoscan during scanningWhen no Signal appears on the screen Autoscan is completeScreen Ratio Selecting screen formatsDisplay menu will appear Screen ratio will be set Press Enter to exit Setup menuScreen ratio options will appear Screen ratio should be selected to fit your TV screenDisplay Mode 43 TV Display mode will be setInformation on 43 TV STBSidebar Letter BoxZoom FullClock menu will appear Setting the clockTime Zone setting menu will appear Daylight savings time setting menu will appearMountain AlaskaHawaii PacificCurrent time setting menu will appear Activated Your settings will be activated4,5,6 Select OFF from the channel-map, then press Enter Will become black on the channel mapChannel search completed. will be indicated Detail menu will appear Setting a new passwordChip / CC Quit Channel Display Clock Detail Your new password is stored Password setting menu will appearCHIP/CC menu will appear CHIP/CC Setting for V-CHIP/CCCHIP/CC password window will appear When choosing STBcontrols V-CHIP Ratings Enter your 4-digit passwordWhen choosing TVcontrols V-CHIP Ratings Press Setup to exit Setup menu Mpaa Rating Setting Mpaa ratingPress Setup to display Setup menu Mpaa rating setting menu will appear When you want to block all PG-13 movies TV Rating Setting TV ratingPress Setup to display Setup menu Information on TV ratings TV rating setting menu will appearQuit Channel CC Selection Selecting CC optionsEnter your 4-digit password Serve as the preferred data channels CC options menu will appearSelected CC option will be set Menu Language Choosing the screen languageLanguage menu will appear Then press EnterTroubleshooting With weak signal Symptom RemedyAudio problems when Using coaxial digitalGlossary and Acronyms SpecificationsMpaa DSTNota Ubicación de los controlesInstalación de las pilas AL Conectar EL Equipo a UNA Caja Para Cable Conexiones de antenaConexión del STB a un Sdtv utilizando la salida Video Configuración inicial Si no desea usar la función de ajuste automático de reloj NuméricosCuando el cursor se encuentre en SET, presione Enter Presione EnterLimited Warranty