Sylvania 6900DTD owner manual Connections STB connection using S-VIDEO output to Sdtv

Page 20

Connections

STB connection using S-VIDEO output to SDTV

NOTE:

S-video cable and audio cable are not included.

Rear panel of STB

Audio cable

To audio input jacks (L, R)

S-video cable

To S-video input jack

1Use a standard antenna cable to connect the wall jack to the ANT IN jack on STB.

2Use a standard audio cable to connect the audio output jacks (L, R) of STB to the audio input jacks (L, R) on the TV.

3Use an S-video cable to connect the S-VIDEO output jack on STB to an S-video input jack on the TV.

4Set the resolution selection switch to “480i.”

5After completing the connection to the TV, plug the AC power cord of the TV into the AC outlet, then turn the TV on.

6Set the TV to the input mode.

NOTE:

Refer to the TV owner’s manual for further information.

7Plug the AC power cord of STB into the AC outlet, then turn STB on.

NOTE:

When using an S-video cable to connect, the resolution of the video signal output will always be 480i.

20

EN

1A23

Image 20

Contents 6900DTD Table of Contents Important Safeguards S2 8 9 8 a Precautions Atsc and Ntsc Information on digital broadcastingReceives both Major features of STB AtscHdtv NtscPower button Power indicatorRemote control sensor Setup buttonRear Panel Remote Control Accessories Installing batteriesSnap the battery cover back Remote controller unit and AA batteries x2 Part No. NE120UDReference to Setup menu Setup WizardChannel DisplayClock Detail Cable BOX When Connecting to Cable BOX AlsoConnections to antenna Right Connections to other devices Connections Connections STB connection using S-VIDEO output to Sdtv Connections STB connection using Video output to Sdtv Connections STB connection to a standard stereo system Stereo ComponentConnections STB connection to a decoder with Dolby Digital Digital DecoderVCR Setup Wizard 1/8 will appear Initial setupSetup Wizard will appear Setup Wizard 3/8 will appear Buttons, then press EnterSTB starts scanning channels To skip the scanningSetup Wizard 5/8 will appear Refer to Information on Time Zones onSelect OFF on the channel map, then press Enter Press Enter when the cursor is on SETWhen not using the auto-clock setting 26-1 Press EnterSelecting a desired channel When using CH o/p buttonsWatching TV When using number buttons E.g., entering 26-1 TV-Y1800 1830 1900 1930 2000 When tuning in a channel from Ntsc Channel bannerPress Info to display a channel banner Press Info to clearDTV LockAudio map Only when tuning in Atsc Choosing audio LanguageWhen tuning in Ntsc Sequence will repeat as shown below when availableWhen tuning in Atsc Press Audio buttonPicture Still Press Still o button while watchingPress any button to quit During STILL, the programs audio will continueNo Signal On screen messagesScanning Restricted ProgramPress EPG button while watching TV EPG will appear on the screenWhen selecting a program being broadcast Select the desired program using o / p Navigation buttonsWhen going back to the previous Components of Electronic Program Guide EPG CC Closed CaptionSetup menu for preference Press Setup to display Setup menu When adding the digital channelAdding channels ADD/ DeleteSelect Channel using o / p navigation Buttons, then press Enter NumberTo add, first enter the digital channel Channel menu will appearSelect ADD using o / p navigation buttons, then press Enter Press Setup to exit Setup menuInformation on Channel Map To continue addingDeleting channels You can add and delete channels in the channel mapDelete To delete the digital channelCursor will move to the channel map Press Enter when the cursor is on the digital channel Will be indicated in the box at the top of the screenDigital channel number 26 will be deleted To continue deletingAdjusting antenna When adjusting the digital channelAntenna Channel 26-1 will be tunedAdjust the antenna direction to get the best reception Receiving the signal strength of the channelWhen adjusting other channels continuously Antenna menu will appear, then STB startsReceiving channels AutoscanSelect Next using s / B navigation buttons, then press Enter To cancel Autoscan during scanning When no Signal appears on the screenAutoscan is complete Verify the antenna connection, then completeDisplay menu will appear Selecting screen formatsScreen Ratio Press Enter to exit Setup menu Screen ratio options will appearScreen ratio should be selected to fit your TV screen Screen ratio will be setDisplay Mode Display mode will be set Information on 43 TVSTB 43 TVLetter Box ZoomFull SidebarSetting the clock Clock menu will appearDaylight savings time setting menu will appear Time Zone setting menu will appearAlaska HawaiiPacific MountainCurrent time setting menu will appear Your settings will be activated Activated4,5,6 Channel search completed. will be indicated Will become black on the channel mapSelect OFF from the channel-map, then press Enter Setting a new password Detail menu will appearChip / CC Quit Channel Display Clock Detail CHIP/CC menu will appear Password setting menu will appearYour new password is stored Setting for V-CHIP/CC CHIP/CCCHIP/CC password window will appear When choosing TVcontrols V-CHIP Ratings Enter your 4-digit passwordWhen choosing STBcontrols V-CHIP Ratings Press Setup to exit Setup menu Setting Mpaa rating Mpaa RatingPress Setup to display Setup menu Mpaa rating setting menu will appear When you want to block all PG-13 movies Setting TV rating TV RatingPress Setup to display Setup menu TV rating setting menu will appear Information on TV ratingsQuit Channel Selecting CC options CC SelectionEnter your 4-digit password Selected CC option will be set CC options menu will appearServe as the preferred data channels Choosing the screen language Menu LanguageThen press Enter Language menu will appearTroubleshooting Symptom Remedy Audio problems whenUsing coaxial digital With weak signalSpecifications Glossary and AcronymsDST MpaaUbicación de los controles NotaInstalación de las pilas Conexiones de antena AL Conectar EL Equipo a UNA Caja Para CableConexión del STB a un Sdtv utilizando la salida Video Configuración inicial Numéricos Cuando el cursor se encuentre en SET, presione EnterPresione Enter Si no desea usar la función de ajuste automático de relojLimited Warranty