Sylvania 6900DTD owner manual Selecting screen formats, Screen Ratio, Display menu will appear

Page 54

Advanced Operation

Selecting screen formats

STB allows you to select a screen ratio and a display mode (aspect ratio) to match the formats of the program being broadcast and your TV screen.

You can also change to aspect ratios you prefer to watch.

SCREEN RATIO

There are two screen ratios used in manufacturing TVs. These are standard TV format (4:3), and widescreen format (16:9).

NOTE:

Aspect ratio is the format for broadcasting and displaying which are defined by the ratio of the screen width to height.

1,5

2,3,4

2,3,4

1Press SETUP to display SETUP menu.

• SETUP menu will appear.

Remote:

Screen:

SETUP

QUIT

CHANNEL

DISPLAY

CLOCK

DETAIL

2 Select DISPLAY using o / p navigation buttons, then press ENTER.

•DISPLAY menu will appear.

DISPLAY

QUIT

CHANNEL

DISPLAY

CLOCK

DETAIL

SCREEN RATIO

DISPLAY MODE

4:3

LETTERBOX

54

EN

1A23

Image 54

Contents 6900DTD Table of Contents Important Safeguards S2 8 9 8 a Precautions Information on digital broadcasting Receives bothAtsc and Ntsc Hdtv Major features of STBAtsc NtscRemote control sensor Power buttonPower indicator Setup buttonRear Panel Remote Control Snap the battery cover back AccessoriesInstalling batteries Remote controller unit and AA batteries x2 Part No. NE120UDReference to Setup menu Setup WizardChannel DisplayClock Detail When Connecting to Cable BOX Also Connections to antennaCable BOX Right Connections to other devices Connections Connections STB connection using S-VIDEO output to Sdtv Connections STB connection using Video output to Sdtv Connections STB connection to a standard stereo system Stereo ComponentConnections STB connection to a decoder with Dolby Digital Digital DecoderVCR Initial setup Setup Wizard will appearSetup Wizard 1/8 will appear STB starts scanning channels Setup Wizard 3/8 will appearButtons, then press Enter To skip the scanningSetup Wizard 5/8 will appear Refer to Information on Time Zones onPress Enter when the cursor is on SET When not using the auto-clock settingSelect OFF on the channel map, then press Enter 26-1 Press EnterWhen using CH o/p buttons Watching TVSelecting a desired channel When using number buttons E.g., entering 26-1 TV-Y1800 1830 1900 1930 2000 Press Info to display a channel banner When tuning in a channel from NtscChannel banner Press Info to clearDTV LockAudio map Only when tuning in Atsc Choosing audio LanguageWhen tuning in Atsc When tuning in NtscSequence will repeat as shown below when available Press Audio buttonPress any button to quit Picture StillPress Still o button while watching During STILL, the programs audio will continueScanning No SignalOn screen messages Restricted ProgramPress EPG button while watching TV EPG will appear on the screenSelect the desired program using o / p Navigation buttons When going back to the previousWhen selecting a program being broadcast Components of Electronic Program Guide EPG CC Closed CaptionSetup menu for preference Adding channels Press Setup to display Setup menuWhen adding the digital channel ADD/ DeleteTo add, first enter the digital channel Select Channel using o / p navigationButtons, then press Enter Number Channel menu will appearInformation on Channel Map Select ADD using o / p navigation buttons, then press EnterPress Setup to exit Setup menu To continue addingDelete Deleting channelsYou can add and delete channels in the channel map To delete the digital channelCursor will move to the channel map Digital channel number 26 will be deleted Press Enter when the cursor is on the digital channelWill be indicated in the box at the top of the screen To continue deletingAntenna Adjusting antennaWhen adjusting the digital channel Channel 26-1 will be tunedWhen adjusting other channels continuously Adjust the antenna direction to get the best receptionReceiving the signal strength of the channel Antenna menu will appear, then STB starts Receiving channels AutoscanSelect Next using s / B navigation buttons, then press Enter Autoscan is complete To cancel Autoscan during scanningWhen no Signal appears on the screen Verify the antenna connection, then completeSelecting screen formats Screen RatioDisplay menu will appear Screen ratio should be selected to fit your TV screen Press Enter to exit Setup menuScreen ratio options will appear Screen ratio will be setDisplay Mode STB Display mode will be setInformation on 43 TV 43 TVFull Letter BoxZoom SidebarSetting the clock Clock menu will appearDaylight savings time setting menu will appear Time Zone setting menu will appearPacific AlaskaHawaii MountainCurrent time setting menu will appear Your settings will be activated Activated4,5,6 Will become black on the channel map Select OFF from the channel-map, then press EnterChannel search completed. will be indicated Setting a new password Detail menu will appearChip / CC Quit Channel Display Clock Detail Password setting menu will appear Your new password is storedCHIP/CC menu will appear Setting for V-CHIP/CC CHIP/CCCHIP/CC password window will appear Enter your 4-digit password When choosing STBcontrols V-CHIP RatingsWhen choosing TVcontrols V-CHIP Ratings Press Setup to exit Setup menu Setting Mpaa rating Mpaa RatingPress Setup to display Setup menu Mpaa rating setting menu will appear When you want to block all PG-13 movies Setting TV rating TV RatingPress Setup to display Setup menu TV rating setting menu will appear Information on TV ratingsQuit Channel Selecting CC options CC SelectionEnter your 4-digit password CC options menu will appear Serve as the preferred data channelsSelected CC option will be set Choosing the screen language Menu LanguageThen press Enter Language menu will appearTroubleshooting Using coaxial digital Symptom RemedyAudio problems when With weak signalSpecifications Glossary and AcronymsDST MpaaUbicación de los controles NotaInstalación de las pilas Conexiones de antena AL Conectar EL Equipo a UNA Caja Para CableConexión del STB a un Sdtv utilizando la salida Video Configuración inicial Presione Enter NuméricosCuando el cursor se encuentre en SET, presione Enter Si no desea usar la función de ajuste automático de relojLimited Warranty