Sylvania 6900DTD owner manual Vcr

Page 24

Connections

STB connection to TV and Video devices (VCR, DVD recorder, etc)

e.g.: Connection to VCR

NOTE:

Audio cables and video cables are not included.

Rear panel of STB

To audio input jacks (L, R)

Audio cable

To video input	Video
jack	cable

Audio cable

VCR

Video cable

1Use a standard antenna cable to connect the wall jack to the ANT IN jack on STB.

2Use a standard audio cable to connect the set of audio output jacks (L, R) on STB to the set of audio input jacks (L, R) on the VCR.

NOTE:

If your VCR is monaural (MONO) and has only one audio jack, use a standard audio cable (white) to connect the audio output jack (white) on STB to the audio input jack (white) on the VCR. The red cable and jack will not be used.

3Use a standard video cable to connect the video output jack on STB to the video input jack on the VCR.

4Set the video resolution selection switch to “480i.”

NOTE:

No matter where the switch is, the video resolution with this connection will be always 480i. For screen ratio and display mode, the settings in Setup menu will be effective.

For the capability of your TV and further information, refer to TV owner’s manual.

5Use a standard video cable to connect the video output jack on the VCR to the video input jack on the TV.

6Use a standard audio cable to connect the set of audio output jacks (L, R) on the VCR to the audio input jacks (L, R) on the TV.

7Plug all AC power cords into AC outlets, then turn all devices on.

8Set the TV and VCR to input mode.

NOTE:

Refer to the owner’s manuals of the TV and the VCR for further information.

NOTE:

When using a standard video cable to connect, the resolution of the video signal output will always be 480i.

24

EN

1A23

Image 24

Contents 6900DTD Table of Contents Important Safeguards S2 8 9 8 a Precautions Information on digital broadcasting Receives bothAtsc and Ntsc Major features of STB AtscHdtv NtscPower button Power indicatorRemote control sensor Setup buttonRear Panel Remote Control Accessories Installing batteriesSnap the battery cover back Remote controller unit and AA batteries x2 Part No. NE120UDReference to Setup menu Setup WizardChannel DisplayClock Detail When Connecting to Cable BOX Also Connections to antennaCable BOX Right Connections to other devices Connections Connections STB connection using S-VIDEO output to Sdtv Connections STB connection using Video output to Sdtv Connections STB connection to a standard stereo system Stereo ComponentConnections STB connection to a decoder with Dolby Digital Digital DecoderVCR Initial setup Setup Wizard will appearSetup Wizard 1/8 will appear Setup Wizard 3/8 will appear Buttons, then press EnterSTB starts scanning channels To skip the scanningSetup Wizard 5/8 will appear Refer to Information on Time Zones onPress Enter when the cursor is on SET When not using the auto-clock settingSelect OFF on the channel map, then press Enter 26-1 Press EnterWhen using CH o/p buttons Watching TVSelecting a desired channel When using number buttons E.g., entering 26-1 TV-Y1800 1830 1900 1930 2000 When tuning in a channel from Ntsc Channel bannerPress Info to display a channel banner Press Info to clearDTV LockAudio map Only when tuning in Atsc Choosing audio LanguageWhen tuning in Ntsc Sequence will repeat as shown below when availableWhen tuning in Atsc Press Audio buttonPicture Still Press Still o button while watchingPress any button to quit During STILL, the programs audio will continueNo Signal On screen messagesScanning Restricted ProgramPress EPG button while watching TV EPG will appear on the screenSelect the desired program using o / p Navigation buttons When going back to the previousWhen selecting a program being broadcast Components of Electronic Program Guide EPG CC Closed CaptionSetup menu for preference Press Setup to display Setup menu When adding the digital channelAdding channels ADD/ DeleteSelect Channel using o / p navigation Buttons, then press Enter NumberTo add, first enter the digital channel Channel menu will appearSelect ADD using o / p navigation buttons, then press Enter Press Setup to exit Setup menuInformation on Channel Map To continue addingDeleting channels You can add and delete channels in the channel mapDelete To delete the digital channelCursor will move to the channel map Press Enter when the cursor is on the digital channel Will be indicated in the box at the top of the screenDigital channel number 26 will be deleted To continue deletingAdjusting antenna When adjusting the digital channelAntenna Channel 26-1 will be tunedAdjust the antenna direction to get the best reception Receiving the signal strength of the channelWhen adjusting other channels continuously Antenna menu will appear, then STB startsReceiving channels AutoscanSelect Next using s / B navigation buttons, then press Enter To cancel Autoscan during scanning When no Signal appears on the screenAutoscan is complete Verify the antenna connection, then completeSelecting screen formats Screen RatioDisplay menu will appear Press Enter to exit Setup menu Screen ratio options will appearScreen ratio should be selected to fit your TV screen Screen ratio will be setDisplay Mode Display mode will be set Information on 43 TVSTB 43 TVLetter Box ZoomFull SidebarSetting the clock Clock menu will appearDaylight savings time setting menu will appear Time Zone setting menu will appearAlaska HawaiiPacific MountainCurrent time setting menu will appear Your settings will be activated Activated4,5,6 Will become black on the channel map Select OFF from the channel-map, then press EnterChannel search completed. will be indicated Setting a new password Detail menu will appearChip / CC Quit Channel Display Clock Detail Password setting menu will appear Your new password is storedCHIP/CC menu will appear Setting for V-CHIP/CC CHIP/CCCHIP/CC password window will appear Enter your 4-digit password When choosing STBcontrols V-CHIP RatingsWhen choosing TVcontrols V-CHIP Ratings Press Setup to exit Setup menu Setting Mpaa rating Mpaa RatingPress Setup to display Setup menu Mpaa rating setting menu will appear When you want to block all PG-13 movies Setting TV rating TV RatingPress Setup to display Setup menu TV rating setting menu will appear Information on TV ratingsQuit Channel Selecting CC options CC SelectionEnter your 4-digit password CC options menu will appear Serve as the preferred data channelsSelected CC option will be set Choosing the screen language Menu LanguageThen press Enter Language menu will appearTroubleshooting Symptom Remedy Audio problems whenUsing coaxial digital With weak signalSpecifications Glossary and AcronymsDST MpaaUbicación de los controles NotaInstalación de las pilas Conexiones de antena AL Conectar EL Equipo a UNA Caja Para CableConexión del STB a un Sdtv utilizando la salida Video Configuración inicial Numéricos Cuando el cursor se encuentre en SET, presione EnterPresione Enter Si no desea usar la función de ajuste automático de relojLimited Warranty