Sylvania 6900DTD owner manual Setup Wizard 5/8 will appear, Refer to Information on Time Zones on

Page 27

Initial Setups (Setup Wizard)

7Select the desired time zone using o / p / s / B navigation buttons, then press

ENTER.

•SETUP WIZARD 5/8 will appear.

SETUP WIZARD 5/8

Enter current time.

YEAR	2001
DATE	--	--	---
TIME	--	--	--
SET

NOTE :

Refer to “INFORMATION on Time Zones ” on page 61.

8Enter YEAR, DATE and TIME using o / p / s / B navigation buttons or number

buttons.

•Every time you enter a number, press ENTER to move the cursor.

•When going back and forth, press s /B navigation buttons to move the cursor.

3 Initial Setups (Setup Wizard)

SETUP WIZARD 5/8

Enter current time.

YEAR	2001
DATE	12	13	THU
TIME	10	30	PM

SET

NOTE:

After all information is entered, the cursor will move to SET.

TIP:

To enter the YEAR, enter the last 2 digits of the year. The year will be entered. (e.g., Enter “03” using number buttons; 2003 will be shown.)

27

EN

1A23

Image 27

Contents 6900DTD Table of Contents Important Safeguards S2 8 9 8 a Precautions Information on digital broadcasting Receives bothAtsc and Ntsc Ntsc Major features of STBAtsc HdtvSetup button Power buttonPower indicator Remote control sensorRear Panel Remote Control Remote controller unit and AA batteries x2 Part No. NE120UD AccessoriesInstalling batteries Snap the battery cover backSetup Wizard Reference to Setup menuDisplay ChannelClock Detail When Connecting to Cable BOX Also Connections to antennaCable BOX Right Connections to other devices Connections Connections STB connection using S-VIDEO output to Sdtv Connections STB connection using Video output to Sdtv Stereo Component Connections STB connection to a standard stereo systemDigital Decoder Connections STB connection to a decoder with Dolby Digital VCR Initial setup Setup Wizard will appearSetup Wizard 1/8 will appear To skip the scanning Setup Wizard 3/8 will appearButtons, then press Enter STB starts scanning channelsRefer to Information on Time Zones on Setup Wizard 5/8 will appearPress Enter when the cursor is on SET When not using the auto-clock settingSelect OFF on the channel map, then press Enter Press Enter 26-1When using CH o/p buttons Watching TVSelecting a desired channel TV-Y When using number buttons E.g., entering 26-11800 1830 1900 1930 2000 Press Info to clear When tuning in a channel from NtscChannel banner Press Info to display a channel bannerLock DTVChoosing audio Language Audio map Only when tuning in AtscPress Audio button When tuning in NtscSequence will repeat as shown below when available When tuning in AtscDuring STILL, the programs audio will continue Picture StillPress Still o button while watching Press any button to quitRestricted Program No SignalOn screen messages ScanningEPG will appear on the screen Press EPG button while watching TVSelect the desired program using o / p Navigation buttons When going back to the previousWhen selecting a program being broadcast CC Closed Caption Components of Electronic Program Guide EPGSetup menu for preference ADD/ Delete Press Setup to display Setup menuWhen adding the digital channel Adding channelsChannel menu will appear Select Channel using o / p navigationButtons, then press Enter Number To add, first enter the digital channelTo continue adding Select ADD using o / p navigation buttons, then press EnterPress Setup to exit Setup menu Information on Channel MapTo delete the digital channel Deleting channelsYou can add and delete channels in the channel map DeleteCursor will move to the channel map To continue deleting Press Enter when the cursor is on the digital channelWill be indicated in the box at the top of the screen Digital channel number 26 will be deletedChannel 26-1 will be tuned Adjusting antennaWhen adjusting the digital channel AntennaAntenna menu will appear, then STB starts Adjust the antenna direction to get the best receptionReceiving the signal strength of the channel When adjusting other channels continuouslyAutoscan Receiving channelsSelect Next using s / B navigation buttons, then press Enter Verify the antenna connection, then complete To cancel Autoscan during scanningWhen no Signal appears on the screen Autoscan is completeSelecting screen formats Screen RatioDisplay menu will appear Screen ratio will be set Press Enter to exit Setup menuScreen ratio options will appear Screen ratio should be selected to fit your TV screenDisplay Mode 43 TV Display mode will be setInformation on 43 TV STBSidebar Letter BoxZoom FullClock menu will appear Setting the clockTime Zone setting menu will appear Daylight savings time setting menu will appearMountain AlaskaHawaii PacificCurrent time setting menu will appear Activated Your settings will be activated4,5,6 Will become black on the channel map Select OFF from the channel-map, then press EnterChannel search completed. will be indicated Detail menu will appear Setting a new passwordChip / CC Quit Channel Display Clock Detail Password setting menu will appear Your new password is storedCHIP/CC menu will appear CHIP/CC Setting for V-CHIP/CCCHIP/CC password window will appear Enter your 4-digit password When choosing STBcontrols V-CHIP RatingsWhen choosing TVcontrols V-CHIP Ratings Press Setup to exit Setup menu Mpaa Rating Setting Mpaa ratingPress Setup to display Setup menu Mpaa rating setting menu will appear When you want to block all PG-13 movies TV Rating Setting TV ratingPress Setup to display Setup menu Information on TV ratings TV rating setting menu will appearQuit Channel CC Selection Selecting CC optionsEnter your 4-digit password CC options menu will appear Serve as the preferred data channelsSelected CC option will be set Menu Language Choosing the screen languageLanguage menu will appear Then press EnterTroubleshooting With weak signal Symptom RemedyAudio problems when Using coaxial digitalGlossary and Acronyms SpecificationsMpaa DSTNota Ubicación de los controlesInstalación de las pilas AL Conectar EL Equipo a UNA Caja Para Cable Conexiones de antenaConexión del STB a un Sdtv utilizando la salida Video Configuración inicial Si no desea usar la función de ajuste automático de reloj NuméricosCuando el cursor se encuentre en SET, presione Enter Presione EnterLimited Warranty