Panasonic AJ-D455P operating instructions Specifications, Other input/output connector

Specifications

GENERAL

	Power supply:	AC 120 V, 50 – 60 Hz
	Power consumption: 95 W
Operating ambient temperature:			41° F to 104° F (5° C to 40° C)
Operating ambient humidity:			10% to 90% (no condensation)
Weight:			31.46 lbs (14.3 kg)
Dimensions (W ⋅ H ⋅		D):	16-3/4 ⋅	6-15/16 ⋅ 16-3/8 inches
Recording format:			(424 ⋅	175.2 ⋅ 415 mm)
			DVCPRO format/DV format
Recording video signals:			525i
Recording audio signals:			48 kHz, 16 bits, 2 channels (DVCPRO)
Recording tracks:			Digital video/audio helical track
			Time code;		Recorded in sub-code area
			Digital audio;		2 channels
			Cue Track;		1 track
Tape speed:			Control (CTL); 1 track
			33.820 mm/sec
Recording time:			126 minutes (with AJ-P126LP)
Tape:			66 minutes (with AJ-P66MP)
			1/4-inch thin magnetic layer metal tape
FF/REW time:			Less than 3 min (with AJ-P126LP)
Editing accuracy:			Less than 2 min (with AJ-P66MP)
			± 0 frame (using time code)
Tape timer accuracy:			± 1 frame (using continuous CTL signal)
Servo lock time:			Less than 0.5 sec. (color framing/
			standby ON)

(Video output connector)

Analog component output:	BNC⋅ 3 (Y, PB, PR)
	Y; 1.0 Vp-p, 75Ω
	PB, PR; 0.486/0.7 Vp-p switchable, 75Ω
	(75% color bar, 7.5% setup)
Analog composite output:	BNC⋅ 3
	Video1/video2/video3 (superimpose
	on/off)
S1 VIDEO output:	S terminal (4-pin)⋅1
	Y; 1.0 Vp-p, 75Ω
	C; 0.286 Vp-p (burst), 75Ω

Serial digital component output

(option):Complies with SMPTE259M-C standard, BNC⋅ 3

(Video output signals adjustment)

Video gain:	± 3 dB
Chroma gain:	± 3 dB
Hue:	± 30°
Setup:	± 14 IRE
Sync phase:	± 15 ∝ s
SC phase:	± 180°

VIDEO
(Digital video)
Sampling frequencies:	Y; 13.5 MHz/PB, PR; 3.375 MHz
Quantizing:	8 bits
Video compression system:	DV-based compression (SMPTE314M)
Video compression ratio:	1/5 (DVCPRO)
Error correction:	Reed-Solomon product code
Video recording/playback bit
rate:	25 Mbps (DVCPRO)
Samples ⋅ number of effective
lines:	720 ⋅ 480/frame (DVCPRO)
(Digital IN/Analog component OUT)
Video bandwidth:	Y; 30 Hz to 5.5 MHz (± 1.0 dB)
	PB, PR; 30 Hz to 1.3 MHz (± 1.0 dB)

AUDIO

(Digital audio)

Sampling frequencies: Quantizing: Frequency response:

Dynamic range:

Distortion:

Crosstalk:

Wow & flutter:

Headroom:

De-emphasis:

48 kHz (synchronized with video signal)

16 bits

20 Hz to 20 kHz (± 1.0 dB) (at reference level)

Better than 85 dB (1 kHz, emphasis OFF, “A” weighted)

Less than 0.1% (1 kHz, emphasis OFF, standard level)

Less than –80 dB (1 kHz, between 2 channels)

Below measurable limits 20 dB

T1=50 ∝ s/T2=15 ∝ s (on/off automatic)

S/N ratio:	Better than 56 dB
K factor:	Less than 2%
(Analog component IN/Analog component OUT)
Video bandwidth:	Y; 30 Hz to 5.5 MHz (–1.5 dB to +1.0 dB)
	PB, PR; 30 Hz to 1.3 MHz
S/N ratio:	(–2.0 dB to +1.0 dB)
	Better than 55 dB
K factor:	Less than 2%
(Analog composite IN/Analog composite OUT)
Video bandwidth:	Y; 30 Hz to 4.5 MHz (–1.5 dB to +1.0 dB)
DG:	Less than 4%
DP:	Less than 3°
Y/C delay:	Better than 20 ns
K factor:	Less than 3%

(Audio input connector)

Analog input (CH1/CH2):	XLR⋅ 2, 600Ω /high impedance selectable,
	+4/0/–20/–60 dBu
Digital input (CH1/CH2):	BNC⋅ 1, AES/EBU format
Serial digital input (option):	Complies with SMPTE259M-C, 272M-A
	standard (BNC, 75Ω )

(Audio output connector)

Analog output (CH1/CH2):	XLR⋅ 2, low impedance, +4/0/–20 dBu
Digital output (CH1/CH2):	BNC⋅ 1, AES/EBU format
Serial digital output (option):	Complies with SMPTE259M-C, 272M-A
	standard (BNC, 75Ω )
Monitor output:	Phono⋅ 1, 600Ω , –8 dBV
Headphones:	Variable level, 1/4" phone, 8Ω

Other input/output connector

S/N ratio: Better than 48 dB

Time code input:

BNC⋅ 1, 0.5 Vp-p to 8 Vp-p, 10 kΩ BNC⋅ 1, 2.0 Vp-p ± 0.5 Vp-p,

(Video input connector)

Analog component input:

Analog composite input:

S1 VIDEO input:

BNC⋅ 3 (Y, PB, PR) Y; 1.0 Vp-p, 75Ω

PB, PR; 0.486/0.7 Vp-p switchable, 75Ω (75% color bar, 7.5% setup)

BNC⋅ 2, loop-through, 75Ω on/off

S terminal (4-pin)⋅1

Y; 1.0 Vp-p, 75Ω

C; 0.286 Vp-p (burst), 75Ω

Time code output:

RS-422A input/output: RS-232C:

Encoder remote:

Digital video interface input/ output (option):

low impedance

D-sub 9-pin, RS-422A interface D-sub 25-pin, RS-232C interface D-sub 15-pin

Compliant with IEEE1394-1995 standard, 6 pins ⋅ 1

Reference input:

Serial digital component input (option):

Analog composite

BNC⋅ 2, loop-through, 75Ω on/off

Complies with SMPTE259M-C standard, BNC⋅ 2, active through

Weight and dimensions when shown are approximately. Specifications are subject to change without notice.

51