Panasonic AJ-D455P Power switch, Cassette insertion slot Eject button, Remote lamp, Wide lamp

Page 7

qPOWER switch

When the ON side is pressed, the power is switched on, and the counter display lights up.

wCassette insertion slot

eEJECT button

When this is pressed, the tape is unloaded and several seconds later the cassette is automatically ejected. When the counter display indicates “CTL”, the display is reset.

rEDIT/EDIT REC/REC/REC INH lamps

EDIT: This lights when the editing mode is chosen from the 9P remote control.

EDIT REC: This lights when editing from the 9P remote control.

REC: This lights during video recording.

REC INH: This lights when the accidental erasure prevention mode has been set for the cassette. In this state, neither recording nor editing is possible.

tREMOTE lamp

This lights when the REMOTE/LOCAL switch has been set to the REMOTE position.

yWIDE lamp

This lights when the unit is in 16:9 wide screen mode.

uTape counter type display

CTL: This indicates the tape timer (control signal).

TC: This indicates the time code.

UB: This indicates the user bit.

No lighting: The remaining tape is displayed.

iSCH lamp

This lights when the SCH phase of the reference video signal is within the prescribed range.

oSERVO lamp

This lights when the drum servo and capstan servo have locked.

!0Channel condition lamps

One of these lamps lights in accordance with the error rate status. (Greenbluered) Green: This lights when the error rates for the video and audio playback signals are both

acceptable.

Blue: This lights when the error rate for the video or audio playback signals has deteriorated.

The playback picture will remain normal even when this lamp lights.

Red: This lights when the video or audio signals are subject to rectification or interpolation.

!1Level meters

These indicate the PCM audio signal CH1/CH2.

The audio signal indicates the input signal levels during recording and EE selection, and the output signal levels during playback.

!2Cassette insertion display lamp

This lights when a cassette has been inserted into the unit.

!3Counter display

This displays the TC and CTL count values, on-screen information and other messages.

7

Image 7
Contents Operating Instructions Do not Open FCC NoteContents Features General and FeaturesAutomatic editing functions from the external controller Menu-driven setupMulti-function input/output interfaces Channel high-sound-quality digital audioFront panel Controls and their functionsCounter Display Section Remote lamp Power switchCassette insertion slot Eject button EDIT/EDIT REC/REC/REC INH lamps6REW button 5RESET button@2Headphones jack 4CTL/TC/UB/REMAIN button@7INT/EXT switch @3Volume control@5SUPER ON/OFF switch @6MONITOR Select switch#2DIAG button #3VIDEO Input switch#4AUDIO Input switch #5REMOTE/LOCAL switchConnector area Analog Component Video in connectors AC in socket Signal GND terminalTime Code IN/OUT connectors Digital Audio IN/OUT connectors7ANALOG Audio OUT connectors 6MONITOR OUT connectorStandard TapesType Description Consumer CassetteFollowing message is displayed Setup default settingsChanging the settings SETUP-MENU Init SET YESPLAY/NOSTOPChanging the file Setup menusSetting and releasing the lock mode Loading a user file Saving a user file Automatic loading of user file when the power is turned onDisplay Setting DescriptionSystem menu SystemVideo output signal adjustments System Setting DescriptionBasic User menuBasic Setting Description Operation Operation Interface Edit Edit Setting Description JOG REV JOG FWDTape Protect Time Code SBC Sub Code Data area Time CodeVaux Video Auxiliary Data area Video Select Video Setting DescriptionVIN Setup WideAudio Audio Setting Description Menu Time code Time code/user bitUser bit Setting the external time code TC switch → EXT Setting the internal time codeRecording internal/external time codes Reproducing the time code/user bit Display position Operation modeSuperimpose screen Characters displayedServo reference Rack mounting Installing the mechanism dust protector Video head cleaningCondensation Diag menu Error messagesDisplaying the Diag menu Item No Description Displaying the Hours Meter informationPriority Counter display Description Monitor display Auto OFF mode IEEE1394 Connector signalsPin No. Signal Signal Pin NoRS-232C Remote 25-pin D-SUB straight cable supported SignalPin No Abbreviation Circuit Description Name Printed circuit boardPrinted Abbr Factory Circuit Full name Function BoardOther input/output connector SpecificationsPanasonic Broadcast & Television Systems Company