Warning display (Displayed regardless of the DISPLAY mode)
When a warning display appears, this unit stops operation and cease to accept any opera- tion commands. When TAPE DEFFECTIVE (5605 - 5609) is displayed, the unit similarly stops operation but accepts one command, viz EJECT.
Display | Status | Action |
|
|
|
| |||
|
|
|
|
|
CONDENSATION | Condensation. | Please leave the power on and wait for the |
|
|
|
| |||
ON DRUM |
| display to disappear. |
|
|
|
|
|
|
|
WARNING 3200 | Unable to load tape. | This error can be resolved by restarting |
|
|
LOADING FAILURE |
| the unit. However, doing so may damage |
|
|
|
| the tape in some cases. Please consult |
|
|
|
|
|
| |
WARNING 3300 | Unable to eject tape. | your PANASONIC authorized dealer. |
|
|
UNLOADING FAILURE |
|
|
|
|
|
|
|
|
|
WARNING 4100 | Eject error. |
|
|
|
|
|
| ||
CASSETTE |
|
|
|
|
EJECT FAILURE |
|
|
|
|
|
|
|
| |
|
|
|
|
|
DEFECTIVE TAPE! | Tape is cut. | Press the EJECT button and retrieve the |
|
|
5605 - 5609 |
| cassette. |
|
|
|
| Then replace the tape. |
|
|
|
|
|
|
|
WARNING 5702 | Tape ending sensor error. | This error can be resolved by restarting |
|
|
TAPE END DET. |
| the unit. However, doing so may damage |
|
|
ERROR! |
| the tape in some cases. Please consult |
|
|
|
| your PANASONIC authorized dealer. |
|
|
WARNING 5802 | Tape begin sensor error. |
|
| |
|
|
| ||
TAPE BEGIN |
|
|
|
|
|
|
|
| |
DET. ERROR! |
|
|
|
|
|
|
|
|
|
WARNING 7001 | Drum rotation error. |
|
|
|
DRUM MOTOR |
|
|
|
|
FAILURE |
|
|
|
|
|
|
|
|
|
WARNING 7101 | Capstan rotation error. |
|
|
|
CAP MOTOR |
|
|
|
|
FAILURE |
|
|
|
|
|
|
|
|
|
WARNING7202 - | Supply reel rotation error. |
|
|
|
7203 |
|
|
|
|
SUPPLY REEL |
|
|
|
|
FAILURE |
|
|
|
|
|
|
|
|
|
WARNING7302 - | Take up reel rotation error. |
|
|
|
7303 |
|
|
|
|
TAKE UP REEL |
|
|
|
|
FAILURE |
|
|
|
|
|
|
|
|
|
WARNING7305 | Tape winding error during unload- |
|
|
|
|
|
| ||
TAKE UP REEL | ing. |
|
|
|
FAILURE |
|
|
|
|
|
|
|
| |
|
|
|
|
|
WARNING 7401 | Reel motor rotation error. |
|
|
|
REEL MOTOR |
|
|
|
|
FAILURE |
|
|
|
|
|
|
|
|
|
UNPLUG MAIN | This is a system error that occurs | Unplug the mains cable from the power |
|
|
POWER, PLUG | when the power is turned on. The | outlet and wait for some time before plug- |
|
|
BACK IN AFTER A | POWER indicator on this unit blinks | ging it back in. |
|
|
WHILE | in green. The unit will not accept any |
|
|
|
| operation commands. |
|
|
|
Memo
This unit uses a microcomputer. It may not function correctly if there is external noise. If this hap- pens, please turn off the power and then on again.