Panasonic AJ- HD3700B manual Plyr

Page 43

Variable memory function

By operating the VTR search dial which is connected to the unit’s RS-422A REMOTE OUT or REMOTE IN/OUT connector, the playback speeds and directions can be stored in the memory, after which the stored contents can be regenerated during automatic editing and stored in the memory of the unit (recorder).

1. Set the F3 (W/PLYR) key to ON.

W/PLYR

ON

∫To operate the VTR connected to the REMOTE OUT connector by remote control, set F5 (PLYR SEL) on the ASSEMBLE/INSERT AUTO EDIT menu to PLAY-1.

∫To operate the VTR connected to the REMOTE IN/OUT connector by remote control, set F5 (PLYR SEL) on the ASSEMBLE/INSERT AUTO EDIT menu to PLAY-2.

2.Set the F4 (VAR MEMO) key to ON.

VAR MEMO

ON

3.Enter the recorder’s VIDEO IN and OUT points together with the player’s IN point.

4.Select PLAYER using the F6 (R/P SEL) key, and set the initial speed using the search dial. The initial speed is displayed on the search indicator.

5.Press the PREVIEW button.

The tape runs as far as the preroll point where playback starts at the initial speed.

6.When the edit IN point is passed, the EXECUTE button’s lamp starts to blink.

7.Set the F6 (R/P SEL) key to PLAYER, and store the speed up to the recorder’s OUT point in the memory using the search dial.

The speed can be stored in the memory while the EXECUTE button’s lamp is blinking until the recorder’s OUT point is reached.

When the memory becomes full, the EXECUTE button’s lamp lights, and no further set- tings can be stored in the memory.

8.To preview the memory contents, press the PREVIEW button, and the memory contents will be regenerated. Phase synchronization is not performed. Adjust the edit timing using the F9 (DLY STRT) key on the ASSEMBLE/INSERT AUTO EDIT SET UP menu.

9.To make changes to the contents stored in the memory while preview is underway, operate the search dial. The EXECUTE button’s lamp now blinks, and the contents are stored in the memory.

10.To make changes to the initial speed which was stored in the memory, press the STOP button.

Set the F6 (R/P SEL) key to PLAYER, and then use the search dial to set the initial speed while holding down the STOP button. Since the memory contents will be cleared when the initial speed is changed, repeat the procedure from step 5.

11.To proceed with variable memory automatic editing, press the REC/EDIT button. The tape in the player is played back in accordance with the memory contents, and the contents are stored in the memory of the unit (recorder).

12.When the PREVIEW/REVIEW button is pressed upon completion of the editing, the editing will be reviewed.

≥The contents stored in the memory are cleared by setting the F10 (VAR MEMO) key from OFF to ON.

≥They are also cleared by setting the power switch to OFF.

– 43 –

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Operating Instructions Hardware Is the safety information For your safety GeneralOperating precaution FCC Note For your safetyFor Your Safety Please Read the Following Text Carefully For your safety EuropeContents Picture/sound quality at a reasonable price FeaturesOperation and maintenance Specifications and interfacesSlow motion, search and editing functions Audio Monitor Controls and their functionsCursor 1415 16UNITY/VAR ≥ENT≥BS ≥FROM ≥COPY28 29 32 TC/CHR SET UP Test DiagVideo Video OUT Audio Audio OUT Button After editing Shtl button JOG button VAR button Search dialEntry button 44454647484950 Fuse Power supply partDigital signal input/output section Connectors BNCt41513141617 Analog input/output sectionCUE OUT Remote Remote control sectionParallel Connection for a single unit ConnectionsConnection for 2 units Connection with an editing controller ONoteN Tapes≥Confirm that the REC Inhibit lamp has gone out Preparation ∑ Release the recording inhibit mode∑ Selecting the input signals and adjusting their levels RecordingOperation Preparation ∑ Setting the time codeSimultaneous playback monitoring ∑ Video monitoring ∑ Checking the input signals∑ Audio monitoring How to display the ≥SYSTEM SET UP menu Menus Home Audio TC/CHR Recording Press the Play button ∑ Monitoring the audio signals∑ Adjusting the audio level Playback∑ Stop Basic operations∑ Jog ∑ Shuttle Shtl∑ Variable VAR ≥Preset variable mode∑ Tape speed override TSO function When TC Input is set to the Standard mode∑ Cue Cue-up operation When TC Input is set to the Reverse modeCeding the cue point by the preroll time Press the F key and Preroll button together. This resultsPress the ENT key ≥Cue points cannot be cleared ∑ Correction of the cue pointMove the cursor to the place which is to be corrected Enter the new value with the number keysManual editing Manual editing Manual audio cross editing Mode FadeAutomatic insert/assemble editing ONoteN ONotesN Audio split editingOUT point preview Set the F3 W/PLYR key to OFF Variable memory FunctionSet the F4 VAR Memo key to on Plyr Connector signals Pin no Signal Direction Type Description ∑ Parallel I/O 50P connector≥50P error status output table FF Status Output Activel Signal Pin No ∑ Storage Video head cleaning∑ Maintenance ∑ OperationRack-mounting How to eject the tape in an emergency TroubleshootingServo microcomputer DIP switch specifications DIP switchAV microcomputer DIP switch specifications Syscon microcomputer DIP switch specificationsGeneral SpecificationsVideo system Input connectorsOutput connectors Video adjustment rangesCue track Audio input connectorsAudio output connectors AudioOptional accessory Audio adjustment rangesOther input/output signals Accessory suppliedPage Panasonic Broadcast Europe
Top Page Image Contents