JVC HR-J270EK Select Preset to Watch, SET Counter Display, Reset Counter, Engage ITR Mode

Page 15

	:–	–
	:–
–	–

PR+/–

RECORD

– –:– –	– –:– –

1 2 3

2

4 5 6

7 8 9

4

00000

PR

1 ?

3

Tape Remaining Time

DISPLAY REMAINING TIME

1 Press – –:– – until the time remaining on the tape appears.

●The display panel shows the tape remaining time

with " " displayed.

●By pressing the – –:– – button, you can change the display to show the counter reading, preset position*, clock time or tape remaining time.

*Preset position is not displayed during playback.

NOTE:

Depending on the type of tape used, there may be times when the tape remaining time reading may not appear right away, or is not correct. "– –:– –" may sometimes appear, or the display may blink on occasion.

15

Record One Programme While Watching Another

SELECT PRESET TO WATCH

1 Once recording is in progress, all you need to do is to set the preset controls on the TV for the station you wish to view.

● The programme selected with the TV’s preset controls appears on the TV screen while the one selected with the recorder's PR buttons is recorded on the tape.

Elapsed Recording Time

Indication

You can check the exact time of a recording.

	1		SET COUNTER DISPLAY
			Press – –:– – until a counter reading appears on the
			display panel.
	2		RESET COUNTER
			Press 0000 before starting recording or playback.

			● The counter is reset to “0:00:00” and shows the exact
			elapsed time as the tape runs.

Instant Timer Recording (ITR)

This easy method allows you to record for any length of time from 30 mins. to 6 hours (selectable in 30-min. increments), and shuts off the recorder after recording is finished.

START RECORDING

1 Press RECORD on the recorder.

ENGAGE ITR MODE

2 Press RECORD again. "" blinks and 0:30 appears on the front display panel.

SET RECORDING

DURATION

3 If you want to record for more than 30 minutes, press RECORD to extend the time. Each press extends recording time by 30 minutes.

NOTE:

You can only perform ITR using the RECORD button on the recorder's front panel.

Image 15

Contents HR-J670EK HR-J672EK HR-J470EK HR-J270EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder To connect to a TV with 21-pin AV input connector ScartBack of TV TV Aerial Cable not providedTion pg and the TV is turned on, Before performing the following procedure, make sure thatAuto for Auto Set Up function Refer toYou will need to start again. See Notes below Or remote control until the display panelShows either the display as illustrated on Progress, this process will be interruptedIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notNexTView Link TV Auto Power OnLink Functions Turn on the RecorderSatellite Receiver Control Setting Access SAT Control SET Screen Enter Satellite RECEIVER’S BrandCheck Result of Test Start Playback PlaybackLoad a Cassette Find Programme Start PointPlayback SearchActivate HIGH-SPEED Search Recording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeEnter Pluscode Number Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Access Video PLUS+ Program ScreenPDC Recording Timer WarningTime Express Timer ProgrammingBefore performing Express Timer Programming Enter Programme Start TimeEngage RECORDER’S SET PDC ModeTimer Mode Return to NormalReturn to Normal SCREEN/ Display Check, Cancel And Replace ProgrammesCancel or Replace a Programme Return to Timer ModeConfirm Overlapping Programmes When programmes overlap each otherCancel or Change Programme Setting To cancel a programmeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsOr press Record on the recorder Start PlaybackRecording PlaybackActivate Index Search Looking For Scene You WantSkip Over Unwanted SectionsDuring Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionTV Aerial cable Aerial Pin AV input Connector ScartAutomatic Satellite Programme Recording Satellite Receiver UnitEngage Auto Satellite Prog REC Mode Access Main Menu ScreenAccess Mode SET Screen Select L-2 Select ModeManually Playback Picture AdjustmentAdjust Tracking Override Automatic TrackingMinimizing Picture Degradation While Editing Access Main Menu ScreenAccess Mode SET Screen Select Picture Control SET ModeEdit From Camcorder Start Source Player Input ModeEdit To Or From Another Video Recorder SET Recording DECK’SSelect Setting To the AV2 L-2 IN/DECODER connectorOff. pg ENABLE/DISABLE ON-SCREEN Display Other FunctionsOn-Screen Display Power SAVE, then press Power Save ModeAuto Timer Auto SP→LP TimerNext Function Memory Repeat Playback Ntsc PlaybackActivate Repeat Playback Audio Cable not provided Speaker Connection To a StereoJust Clock Clock SetVideo Plus+ Setup NumberGuide Program Number Set SET Video Channel Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection CH SET Tuner SetPerform Auto Channel SET Auto Channel SetIs displayed on the screen Screen preset positionsProcedures After Scan CompletedEnter NEW Channel Information Storing Channels ManuallySelect Band Input ChannelDelete a Channel When Receiving a Scrambled BroadcastChange Station Preset Position Fine-Tuning Channels Already StoredSelect NEW Station Access ManualSwitch Stations Channel SET ScreenTV Station And ID List TV Station Channel Number Guide Questions And Answers Ä remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Troubleshooting Won’t stop Timer RecordingFront View IndexRecord Pause AV1 L-1 IN/OUT Connector enables AV connecProgramme Time Indicators show the programme Tape Remaining Time Indicator displays time remainingRemote Control VCR, TV PR +/-,TV +/-, TV Muting Fast Forward FF Button fast-forwards tapeVHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical Rotary two-head herical scan