JVC HR-J670EK, HR-J672EK Check, Cancel And Replace Programmes, Cancel or Replace a Programme

Page 20

20

BASICOPERATIONS(cont.)

Check, Cancel And Replace

Programmes

1

4

PDC 7

START+/–

1	–

STOP+/

– –:– –

2 3

2

56

89

4

0

	PR+/–
?	DATE+/
?
	–
	SP/LP
3	OK

DISENGAGE TIMER MODE

1 Press ä, then press

.

ACCESS PROGRAMME CHECK

2

SCREEN/DISPLAY

Press .

START

STOP

CH

DATE

1

8 : 00

10 : 00

3

24 . 12

2

10 : 00

10 : 45

2

25 . 12

3

11 : 30

13 : 00

1

25 . 12

4

5

6

7

8

[

] : NEXT

ACCESS PROGRAMME SCREEN/

DISPLAY

Press again to check

– P1 –

more information. Each

START

STOP

time you press

, the

8:00

=

10:00

3 next programme's

information appears.

SP

VPS/PDC OFF

DATE

TV PROG

24.12

3

ITV

[

] : NEXT

SP

●The display panel shows the programme start time. Pressing OK changes the display to the programme stop time, then the date and the preset position.

NOTE:

You can also check the programmes on the display panel even if the recorder's power is off (unless the recorder is in the Power Save mode ☞ pg. 34) or the recorder is in the Timer mode; however, it is not possible to cancel or replace the programmes.

To cancel or replace a programme...

CANCEL OR REPLACE A

PROGRAMME

4	Press to cancel a programme. To replace a
	programme, press the appropriate button: START+/–,
	STOP+/–,DATE+/–,PR+/–,SP/LP (	), PDC.

●You can change "TV PROG" to "SAT" for the preset position by pressing the NUMBER key "0".

RETURN TO NORMAL SCREEN/ DISPLAY

5 Press as many times as necessary. If there are still some programmes to be recorded, go on to step 6.

RETURN TO TIMER MODE

6 Press ä.

Image 20

Contents HR-J670EK HR-J672EK HR-J470EK HR-J270EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide To connect to a TV with 21-pin AV input connector Scart Back of TVTV Aerial Cable not provided Back of RecorderBefore performing the following procedure, make sure that Auto for Auto Set Up functionRefer to Tion pg and the TV is turned on,Or remote control until the display panel Shows either the display as illustrated onProgress, this process will be interrupted You will need to start again. See Notes belowIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedTV Auto Power On Link FunctionsTurn on the Recorder NexTView LinkSatellite Receiver Control Setting Check Result of Test Access SAT Control SET ScreenEnter Satellite RECEIVER’S Brand Playback Load a CassetteFind Programme Start Point Start PlaybackActivate HIGH-SPEED Search PlaybackSearch Recording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingEnter Programme Start Time TimeSET PDC Mode Timer ModeReturn to Normal Engage RECORDER’SCheck, Cancel And Replace Programmes Cancel or Replace a ProgrammeReturn to Timer Mode Return to Normal SCREEN/ DisplayWhen programmes overlap each other Cancel or Change Programme SettingTo cancel a programme Confirm Overlapping ProgrammesPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemStart Playback RecordingPlayback Or press Record on the recorderLooking For Scene You Want Skip Over UnwantedSections Activate Index SearchSelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackAerial Pin AV input Connector Scart Automatic Satellite Programme RecordingSatellite Receiver Unit TV Aerial cableAccess Main Menu Screen Access Mode SET ScreenSelect L-2 Select Mode Engage Auto Satellite Prog REC ModePlayback Picture Adjustment Adjust TrackingOverride Automatic Tracking ManuallyAccess Main Menu Screen Access Mode SET ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Input Mode Edit To Or From Another Video RecorderSET Recording DECK’S Start Source PlayerOff. pg Select SettingTo the AV2 L-2 IN/DECODER connector On-Screen Display ENABLE/DISABLE ON-SCREEN DisplayOther Functions Power Save Mode Power SAVE, then pressNext Function Memory Auto TimerAuto SP→LP Timer Activate Repeat Playback Repeat PlaybackNtsc Playback Connection To a Stereo Audio Cable not provided SpeakerClock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Access Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Tuner Set Perform Auto Channel SETAuto Channel Set CH SETScreen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Select BandInput Channel Enter NEW Channel InformationWhen Receiving a Scrambled Broadcast Change Station Preset PositionFine-Tuning Channels Already Stored Delete a ChannelAccess Manual Switch StationsChannel SET Screen Select NEW StationTV Station And ID List TV Station Channel Number Guide What happens if the tape runs out during recording? Questions And AnswersÄ remain lit on the display panel. Is there Problem? Troubleshooting Timer Recording Won’t stopIndex Front ViewAV1 L-1 IN/OUT Connector enables AV connec Programme Time Indicators show the programmeTape Remaining Time Indicator displays time remaining Record PauseRemote Control Fast Forward FF Button fast-forwards tape VCR, TV PR +/-,TV +/-, TV MutingMaximum recording time DA4 Double Azimuth helicalRotary two-head herical scan VHF 44.5 143/143 470 MHz