JVC HR-J672EK, HR-J670EK, HR-J470EK, HR-J270EK setup guide With RF Connection

Page 41

STOP

– –:– –

1 2 3

2

4 5 6

7 8 9

4

0

PR

1 ?

OK

TEST SIGNAL

The channel on which the screen on the left appears clearly in step 2 is your Video Channel.

41

With RF Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■the connected TV is turned on.

■batteries have been installed in the remote control.

ACCESS VIDEO CHANNEL

SET MODE

1 Press and hold down STOP on the recorder until the display panel shows the following.

SET VIDEO CHANNEL

2 Press PR+ or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area. Refer to list on page 48 for details of broadcast stations in your area.

(Ex.) If channel 36 is available in your area

Then set your TV to UHF channel 36. (Refer to the instructions supplied with your TV set for how to do this.)

●If the two vertical white bars appear clearly on the screen as shown in the illustration at bottom left, go to step 3.

●If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.

IMPORTANT

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

EXIT VIDEO CHANNEL SET

MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to the Video Channel.

Image 41

Contents HR-J670EK HR-J672EK HR-J470EK HR-J270EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of TV To connect to a TV with 21-pin AV input connector ScartTV Aerial Cable not provided Back of RecorderAuto for Auto Set Up function Before performing the following procedure, make sure thatRefer to Tion pg and the TV is turned on,Shows either the display as illustrated on Or remote control until the display panelProgress, this process will be interrupted You will need to start again. See Notes belowIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notLink Functions TV Auto Power OnTurn on the Recorder NexTView LinkSatellite Receiver Control Setting Check Result of Test Access SAT Control SET ScreenEnter Satellite RECEIVER’S Brand Load a Cassette PlaybackFind Programme Start Point Start PlaybackActivate HIGH-SPEED Search PlaybackSearch Recording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayAccess Video PLUS+ Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Program Screen Enter Pluscode NumberPDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET PDC ModeReturn to Normal Engage RECORDER’SCancel or Replace a Programme Check, Cancel And Replace ProgrammesReturn to Timer Mode Return to Normal SCREEN/ DisplayCancel or Change Programme Setting When programmes overlap each otherTo cancel a programme Confirm Overlapping ProgrammesS.T. Picture System Playback/ Recording According To Tape Charac- teristicsRecording Start PlaybackPlayback Or press Record on the recorderSkip Over Unwanted Looking For Scene You WantSections Activate Index SearchReceiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackAutomatic Satellite Programme Recording Aerial Pin AV input Connector ScartSatellite Receiver Unit TV Aerial cableAccess Mode SET Screen Access Main Menu ScreenSelect L-2 Select Mode Engage Auto Satellite Prog REC ModeAdjust Tracking Playback Picture AdjustmentOverride Automatic Tracking ManuallyAccess Mode SET Screen Access Main Menu ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Edit To Or From Another Video Recorder Input ModeSET Recording DECK’S Start Source PlayerOff. pg Select SettingTo the AV2 L-2 IN/DECODER connector On-Screen Display ENABLE/DISABLE ON-SCREEN DisplayOther Functions Power SAVE, then press Power Save ModeNext Function Memory Auto TimerAuto SP→LP Timer Activate Repeat Playback Repeat PlaybackNtsc Playback Audio Cable not provided Speaker Connection To a StereoJust Clock Clock SetGuide Program Number Set Video Plus+ SetupNumber Exit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Perform Auto Channel SET Tuner SetAuto Channel Set CH SETProcedures Screen preset positionsAfter Scan Completed Is displayed on the screenSelect Band Storing Channels ManuallyInput Channel Enter NEW Channel InformationChange Station Preset Position When Receiving a Scrambled BroadcastFine-Tuning Channels Already Stored Delete a ChannelSwitch Stations Access ManualChannel SET Screen Select NEW StationTV Station And ID List TV Station Channel Number Guide What happens if the tape runs out during recording? Questions And AnswersÄ remain lit on the display panel. Is there Problem? Troubleshooting Won’t stop Timer RecordingFront View IndexProgramme Time Indicators show the programme AV1 L-1 IN/OUT Connector enables AV connecTape Remaining Time Indicator displays time remaining Record PauseRemote Control VCR, TV PR +/-,TV +/-, TV Muting Fast Forward FF Button fast-forwards tapeDA4 Double Azimuth helical Maximum recording timeRotary two-head herical scan VHF 44.5 143/143 470 MHz