JVC HR-J670EK Load a Cassette, Find Programme Start Point, Start Playback, Stop Playback

Page 12

12

BASICOPERATIONS

Playback

Turn on the TV and select the VIDEO channel (or AV mode).

The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.

LOAD A CASSETTE

1 Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the recorder. Don’t apply too much

1

2

EW

 

PR+/–

 

– –:– –

TV/VCR

1 2 3

2

4 5 6

7 8 9

4

0

3

LAY1

?

2 REW

4 STOP

3

3

PLAY

STOP/EJECT

4

PR

FF2

PAUSE

2

FF

PAUSE

pressure when inserting.

● The recorder power comes on automatically and the counter is reset to 0:00:00.

● If the record safety tab has been removed, playback begins automatically.

2

FIND PROGRAMME START POINT

If the tape is advanced past the start point, press REW.

To go forward, press FF.

3

START PLAYBACK

Press PLAY. "BEST" appears blinking in the recorder's

display panel during automatic tracking (☞ pg. 22).

● Playback picture quality of LP recordings will not be

 

 

as high as SP recordings.

 

 

 

STOP PLAYBACK

 

Press STOP on the remote or STOP/EJECT on the

 

recorder’s front panel. Then press STOP/EJECT to

4 remove the cassette.

Clean the video heads using a dry cleaning cassette — JVC TCL-2U — when:

●Rough, poor picture appears while a tape is played back.

●The picture is unclear or no picture appears.

●"USE CLEANING CASSETTE" appears on the screen (only with "O.S.D." set to "ON" (☞ pg. 33.)

INFORMATION

When using the AV connection (☞ pg. 5), initiating playback causes the VCR indicator to light and the TV to automatically enter AV mode. To return the TV to TV mode after playback is complete, press TV/VCR so that the VCR indicator turns off.

*Depending on the type of TV used, TV/VCR button does not always function as described above.

Tape Position Indicator

The tape position indicator appears on screen when, from the Stop mode, you press FF, REW or perform an Index Search. The position of “5” in relation to “0” (beginning) or “+” (end)

shows you where you are on 0 + the tape.

”O.S.D.” (☞ pg. 33) must

be set to “ON”, or the

indicator will not appear. Beginning

3

+ +

1:23:45 REMAIN 2:35

End

Usable cassettes

● Compact VHS camcorder recordings can be played on

this video recorder. Simply place the recorded cassette

into a VHS Cassette Adapter and it can be used just like

any full-sized VHS cassette.

● This video recorder can record on regular VHS and

NOTE:

Depending on the type of tape used, there may be times when the indication is not correct.

Super VHS cassettes. However, it will record and play

back regular VHS signals only. It is not possible to play

back a recorded Super VHS tape.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents HR-J670EK HR-J672EK HR-J470EK HR-J270EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide To connect to a TV with 21-pin AV input connector Scart Back of TVTV Aerial Cable not provided Back of RecorderBefore performing the following procedure, make sure that Auto for Auto Set Up functionRefer to Tion pg and the TV is turned on,Or remote control until the display panel Shows either the display as illustrated onProgress, this process will be interrupted You will need to start again. See Notes belowIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedTV Auto Power On Link FunctionsTurn on the Recorder NexTView LinkSatellite Receiver Control Setting Access SAT Control SET Screen Enter Satellite RECEIVER’S BrandCheck Result of Test Playback Load a CassetteFind Programme Start Point Start PlaybackPlayback SearchActivate HIGH-SPEED Search Recording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingEnter Programme Start Time TimeSET PDC Mode Timer ModeReturn to Normal Engage RECORDER’SCheck, Cancel And Replace Programmes Cancel or Replace a ProgrammeReturn to Timer Mode Return to Normal SCREEN/ DisplayWhen programmes overlap each other Cancel or Change Programme SettingTo cancel a programme Confirm Overlapping ProgrammesPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemStart Playback RecordingPlayback Or press Record on the recorderLooking For Scene You Want Skip Over UnwantedSections Activate Index SearchSelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackAerial Pin AV input Connector Scart Automatic Satellite Programme RecordingSatellite Receiver Unit TV Aerial cableAccess Main Menu Screen Access Mode SET ScreenSelect L-2 Select Mode Engage Auto Satellite Prog REC ModePlayback Picture Adjustment Adjust TrackingOverride Automatic Tracking ManuallyAccess Main Menu Screen Access Mode SET ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Input Mode Edit To Or From Another Video RecorderSET Recording DECK’S Start Source PlayerSelect Setting To the AV2 L-2 IN/DECODER connectorOff. pg ENABLE/DISABLE ON-SCREEN Display Other FunctionsOn-Screen Display Power Save Mode Power SAVE, then pressAuto Timer Auto SP→LP TimerNext Function Memory Repeat Playback Ntsc PlaybackActivate Repeat Playback Connection To a Stereo Audio Cable not provided SpeakerClock Set Just ClockVideo Plus+ Setup NumberGuide Program Number Set Access Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Tuner Set Perform Auto Channel SETAuto Channel Set CH SETScreen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Select BandInput Channel Enter NEW Channel InformationWhen Receiving a Scrambled Broadcast Change Station Preset PositionFine-Tuning Channels Already Stored Delete a ChannelAccess Manual Switch StationsChannel SET Screen Select NEW StationTV Station And ID List TV Station Channel Number Guide Questions And Answers Ä remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Troubleshooting Timer Recording Won’t stopIndex Front ViewAV1 L-1 IN/OUT Connector enables AV connec Programme Time Indicators show the programmeTape Remaining Time Indicator displays time remaining Record PauseRemote Control Fast Forward FF Button fast-forwards tape VCR, TV PR +/-,TV +/-, TV MutingMaximum recording time DA4 Double Azimuth helicalRotary two-head herical scan VHF 44.5 143/143 470 MHz
Top Page Image Contents