JVC HR-J470EK, HR-J670EK, HR-J672EK, HR-J270EK setup guide Troubleshooting

Page 50

50

SUBSIDIARYINFORMATION(cont.)

Troubleshooting

Before requesting service for a problem, use this chart to see if you can correct the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair.

POWER

SYMPTOM

1.No power is applied to the recorder.

2.The clock is functioning properly, but the recorder cannot be powered.

3.The remote control won’t function.

TAPE TRANSPORT

SYMPTOM

1.The tape does not run during recording.

2.The tape will not rewind or fast- forward.

PLAYBACK

SYMPTOM

1.The playback picture does not appear while the tape is running.

2.Noise appears during visual search.

3.Noise appears during normal playback.

4.The playback picture is blurred or interrupted while TV broadcasts are clear or "USE CLEANING CASSETTE" message appears on the screen.

5.Breaks are noticeable in Hi-Fi soundtrack. (HR-J670/672EK only)

RECORDING

SYMPTOM

1.Recording cannot be started.

2.TV broadcasts cannot be recorded.

3.Tape-to-tape editing is not possible.

POSSIBLE CAUSE

The mains power cord is disconnected.

“ä“ is displayed on the display panel with Auto Timer set to "OFF".

The batteries are discharged.

POSSIBLE CAUSE

“ is displayed on the display panel.

The tape is already fully rewound or fast-forwarded.

POSSIBLE CAUSE

If you’re using the RF connection . . .

. . . the TV receiver’s channel selector is not set to the VIDEO channel.

. . . the recorder's VIDEO channel has not been correctly set.

If you’re using the AV connection, the TV receiver is not set to the AV mode.

This is normal.

The automatic tracking mode is engaged.

The video heads may be dirty.

Automatic tracking is engaged.

POSSIBLE CAUSE

There is no cassette loaded, or the cassette loaded has had its Record Safety tab removed.

“L-1”, “L-2”, “SAT” or “F-1” has been selected as the input mode. (“F-1” is for HR-J670/672EK only.)

The source (another video recorder, camcorder) has not been properly connected.

All necessary power switches have not been turned on.

The input mode is not correct.

CORRECTIVE ACTION

Connect the mains power cord.

Press the äbutton to turn the “ä“ indicator off.

Replace the dead batteries with new ones.

CORRECTIVE ACTION

Press PLAY to turn the ““ indicator off.

Check the cassette.

CORRECTIVE ACTION

If you are using the RF connection . . .

. . . set the TV receiver to the VIDEO channel. (pg. 6)

. . . Perform "Video Channel Set" (pg. 40)

If you are using the AV connection, set the TV to its AV mode.

Try manual tracking (pg. 28).

Use a dry cleaning cassette JVC TCL-2U or consult your JVC dealer.

Engage and adjust tracking manually (pg. 28) or press AUDIO to change the soundtrack to "NORM" (Ê pg.Ê 25).

CORRECTIVE ACTION

Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed.

Set to the desired preset.

Confirm that the source is properly connected.

Confirm that all units’ power switches are turned on.

Set the input mode to “L-1”,“L-2” or “F-1”. (“F-1” is for HR-J670/672EK only.)

Image 50
Contents HR-J670EK HR-J672EK HR-J470EK HR-J270EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide TV Aerial Cable not provided To connect to a TV with 21-pin AV input connector ScartBack of TV Back of RecorderRefer to Before performing the following procedure, make sure thatAuto for Auto Set Up function Tion pg and the TV is turned on,Progress, this process will be interrupted Or remote control until the display panelShows either the display as illustrated on You will need to start again. See Notes belowIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedTurn on the Recorder TV Auto Power OnLink Functions NexTView LinkSatellite Receiver Control Setting Check Result of Test Access SAT Control SET ScreenEnter Satellite RECEIVER’S Brand Find Programme Start Point PlaybackLoad a Cassette Start PlaybackActivate HIGH-SPEED Search PlaybackSearch Recording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayAccess Video PLUS+ Program Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Enter Pluscode NumberTimer Warning PDC RecordingEnter Programme Start Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode Engage RECORDER’SReturn to Timer Mode Check, Cancel And Replace ProgrammesCancel or Replace a Programme Return to Normal SCREEN/ DisplayTo cancel a programme When programmes overlap each otherCancel or Change Programme Setting Confirm Overlapping ProgrammesPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemPlayback Start PlaybackRecording Or press Record on the recorderSections Looking For Scene You WantSkip Over Unwanted Activate Index SearchSoundtrack Selection Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes During PlaybackSatellite Receiver Unit Aerial Pin AV input Connector ScartAutomatic Satellite Programme Recording TV Aerial cableSelect L-2 Select Mode Access Main Menu ScreenAccess Mode SET Screen Engage Auto Satellite Prog REC ModeOverride Automatic Tracking Playback Picture AdjustmentAdjust Tracking ManuallySelect Picture Control SET Mode Access Main Menu ScreenAccess Mode SET Screen Minimizing Picture Degradation While EditingEdit From Camcorder SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Start Source PlayerOff. pg Select SettingTo the AV2 L-2 IN/DECODER connector On-Screen Display ENABLE/DISABLE ON-SCREEN DisplayOther Functions Power Save Mode Power SAVE, then pressNext Function Memory Auto TimerAuto SP→LP Timer Activate Repeat Playback Repeat PlaybackNtsc Playback Connection To a Stereo Audio Cable not provided SpeakerClock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Video Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelWith RF Connection Auto Channel Set Tuner SetPerform Auto Channel SET CH SETAfter Scan Completed Screen preset positionsProcedures Is displayed on the screenInput Channel Storing Channels ManuallySelect Band Enter NEW Channel InformationFine-Tuning Channels Already Stored When Receiving a Scrambled BroadcastChange Station Preset Position Delete a ChannelChannel SET Screen Access ManualSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide What happens if the tape runs out during recording? Questions And AnswersÄ remain lit on the display panel. Is there Problem? Troubleshooting Timer Recording Won’t stopIndex Front ViewTape Remaining Time Indicator displays time remaining AV1 L-1 IN/OUT Connector enables AV connecProgramme Time Indicators show the programme Record PauseRemote Control Fast Forward FF Button fast-forwards tape VCR, TV PR +/-,TV +/-, TV MutingRotary two-head herical scan Maximum recording timeDA4 Double Azimuth helical VHF 44.5 143/143 470 MHz