JVC HR-J670EK, HR-J672EK Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 40

40SUBSIDIARYSETTINGS(cont.)

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

IMPORTANT

Perform the following steps only if —

—Video Channel Set has not been done correctly by the Auto Set Up function (☞ pg. 6).

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV connection, or vice versa.

●If you have connected the video recorder to your TV via both the provided RF cable and a

21-pin SCART cable (AV connection), you do not need the video channel so you have to set the video channel to off. — Go to "With AV Connection" below.

●If you have connected the video recorder to your TV via the provided RF cable only (RF connection), you have to set the correct video channel — Go to "With RF Connection" on page 41.

STOP

With AV Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■ batteries have been installed in the remote control.

– –:– –

1 2 3

2

4 5 6

7 8 9

4

0

PR

1 ?

OK

1

2

3

ACCESS VIDEO CHANNEL SET MODE

Press and hold down STOP on the recorder until the display panel shows the following.

SET VIDEO CHANNEL

Press PR – until the display panel shows "–OUT– –".

●Now the video channel is set to off.

EXIT VIDEO CHANNEL SET MODE

Press OK.

To view picture signals from the video recorder, set your TV to its AV mode. Refer to the instructions supplied with your TV set for how to do this.

Image 40

Contents HR-J670EK HR-J672EK HR-J470EK HR-J270EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide To connect to a TV with 21-pin AV input connector Scart Back of TVTV Aerial Cable not provided Back of RecorderBefore performing the following procedure, make sure that Auto for Auto Set Up functionRefer to Tion pg and the TV is turned on,Or remote control until the display panel Shows either the display as illustrated onProgress, this process will be interrupted You will need to start again. See Notes belowIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedTV Auto Power On Link FunctionsTurn on the Recorder NexTView LinkSatellite Receiver Control Setting Enter Satellite RECEIVER’S Brand Access SAT Control SET ScreenCheck Result of Test Playback Load a CassetteFind Programme Start Point Start PlaybackSearch PlaybackActivate HIGH-SPEED Search Recording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingEnter Programme Start Time TimeSET PDC Mode Timer ModeReturn to Normal Engage RECORDER’SCheck, Cancel And Replace Programmes Cancel or Replace a ProgrammeReturn to Timer Mode Return to Normal SCREEN/ DisplayWhen programmes overlap each other Cancel or Change Programme SettingTo cancel a programme Confirm Overlapping ProgrammesPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemStart Playback RecordingPlayback Or press Record on the recorderLooking For Scene You Want Skip Over UnwantedSections Activate Index SearchSelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackAerial Pin AV input Connector Scart Automatic Satellite Programme RecordingSatellite Receiver Unit TV Aerial cableAccess Main Menu Screen Access Mode SET ScreenSelect L-2 Select Mode Engage Auto Satellite Prog REC ModePlayback Picture Adjustment Adjust TrackingOverride Automatic Tracking ManuallyAccess Main Menu Screen Access Mode SET ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Input Mode Edit To Or From Another Video RecorderSET Recording DECK’S Start Source PlayerTo the AV2 L-2 IN/DECODER connector Select SettingOff. pg Other Functions ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Display Power Save Mode Power SAVE, then pressAuto SP→LP Timer Auto TimerNext Function Memory Ntsc Playback Repeat PlaybackActivate Repeat Playback Connection To a Stereo Audio Cable not provided SpeakerClock Set Just ClockNumber Video Plus+ SetupGuide Program Number Set Access Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Tuner Set Perform Auto Channel SETAuto Channel Set CH SETScreen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Select BandInput Channel Enter NEW Channel InformationWhen Receiving a Scrambled Broadcast Change Station Preset PositionFine-Tuning Channels Already Stored Delete a ChannelAccess Manual Switch StationsChannel SET Screen Select NEW StationTV Station And ID List TV Station Channel Number Guide Ä remain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Timer Recording Won’t stopIndex Front ViewAV1 L-1 IN/OUT Connector enables AV connec Programme Time Indicators show the programmeTape Remaining Time Indicator displays time remaining Record PauseRemote Control Fast Forward FF Button fast-forwards tape VCR, TV PR +/-,TV +/-, TV MutingMaximum recording time DA4 Double Azimuth helicalRotary two-head herical scan VHF 44.5 143/143 470 MHz