JVC HR-J672EK, HR-J670EK, HR-J470EK, HR-J270EK setup guide Timer Warning, PDC Recording

Page 17

 

SET TAPE SPEED

4 Press SP/LP (

) to set the tape speed.

5

SET PDC MODE

Press PDC to select "ON" or "OFF".

If "VPS/PDC ON" is displayed on the screen or "VPS/

PDC" is lit on the display panel, PDC is set to ON.

 

If "VPS/PDC OFF" is displayed on the screen or "VPS/

 

PDC" is not lit on the display panel, PDC is set to OFF.

 

☞ "PDC Recording" in the column below.

 

● VPS (Video Programme System) recording is not

 

currently available in the U.K. and not possible with

 

this recorder.

 

 

RETURN TO NORMAL SCREEN

 

Press PROG or OK. "PROGRAM COMPLETED" appears

 

on the screen for about 5 seconds, then normal screen

6 appears. If the timer programme is overlapped with

 

another one that was already set, "PROGRAM

17

Satellite Receiver Users

To timer-record a satellite broadcast using VIDEO Plus+: 1 Perform "Satellite Receiver Control Setting" (☞ pg. 10). 2 Perform steps 1 – 7. In step 3, the display panel shows "L2" for the preset position. In step 5, you cannot set

PDC to ON.

3 Leave the satellite receiver's power on.

ATTENTION

Regarding Guide Program Number Set

"GUIDE PROG SET" appears after performing step 3 if the Guide Program number for the PlusCode number you entered has not been set.

● If you want to set the Guide Program number for the satellite broadcast station, press the NUMBER key "0" to change "TV PROG" to "SAT". Press %Þ to input the preset position number on which your recorder or satellite receiver receives that station, then press OK or # to set the Guide Program Number. The VIDEO Plus+ Program screen appears.

 

OVERLAPPED" appears on screen and "Err" appears on

 

the front display panel. (☞ pg. 21)

 

 

 

● Repeat steps 1 – 6 for each additional programme.

 

 

 

ENGAGE RECORDER’S TIMER

7

MODE

Press ä (TIMER). The recorder turns off automatically

and ä appears on the display panel.

 

● To disengage the timer, press ä (TIMER) again.

GUIDE PROG SET

GUIDE PROG

TV PROG

2

– –

[5°] =

[0] : SAT

[PROG] : EXIT

 

(Ex.) To timer-record a BBC2 programme with VIDEO Plus+.

*If your recorder receives BBC2 on the preset position 2, press OK or #after entering "2" using %Þ buttons.

NOTES:

● To Change The Stop Time . . .

. . . press STOP +/– after pressing OK in step 3. You can

compensate for anticipated programme schedule delays this

way.

● To Timer-Record Weekly Or Daily Serials . . .

. . . after pressing OK in step 3, press WEEKLY (NUMBER key

“9”) for weekly serials or DAILY (NUMBER key “8”) for daily

Timer Warning

If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on the screen to tell you that the recording is due to start in 5 minutes.

–WARNING– TIMER RECORDING

TO START SOON

[]

serials (Monday – Friday). Either "WEEKLY" or "DAILY"

appears on the screen. Pressing the button again makes the

corresponding indication disappear.

● You can programme this recorder to timer-record as many as 8

programmes. If you try to programme the recorder to record a

ninth, "PROGRAM FULL" appears on screen and "FULL"

appears on the front display panel. To record the extra

programme, you must first cancel any unnecessary

programmes (☞ pg. 20).

● It is not possible to timer-record a TV programme with a

PlusCode number which starts with "0".

NOTES:

●The warning only appears if you’re not in the Timer mode at the time.

●If this recorder is being used as the player for tape dubbing, the warning screen will be recorded on the tape in the other video recorder.

The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press .

PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times which you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service in some areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be sure to set PDC to "OFF" if PDC is not available on your selected channel (☞ step 5 above).

NOTES:

●PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 (L-2) IN/DECODER on your recorder.

●PDC recording is also possible via the AV1 (L-1) IN/OUT connector.

Page 16 Page 18
Image 17
Page 16 Page 18
Contents HR-J670EK HR-J672EK HR-J470EK HR-J270EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of TV To connect to a TV with 21-pin AV input connector ScartTV Aerial Cable not provided Back of RecorderAuto for Auto Set Up function Before performing the following procedure, make sure thatRefer to Tion pg and the TV is turned on,Shows either the display as illustrated on Or remote control until the display panelProgress, this process will be interrupted You will need to start again. See Notes belowIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notLink Functions TV Auto Power OnTurn on the Recorder NexTView LinkSatellite Receiver Control Setting Check Result of Test Access SAT Control SET ScreenEnter Satellite RECEIVER’S Brand Load a Cassette PlaybackFind Programme Start Point Start PlaybackActivate HIGH-SPEED Search PlaybackSearch Recording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayAccess Video PLUS+ Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Program Screen Enter Pluscode NumberPDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET PDC ModeReturn to Normal Engage RECORDER’SCancel or Replace a Programme Check, Cancel And Replace ProgrammesReturn to Timer Mode Return to Normal SCREEN/ DisplayCancel or Change Programme Setting When programmes overlap each otherTo cancel a programme Confirm Overlapping ProgrammesS.T. Picture System Playback/ Recording According To Tape Charac- teristicsRecording Start PlaybackPlayback Or press Record on the recorderSkip Over Unwanted Looking For Scene You WantSections Activate Index SearchReceiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackAutomatic Satellite Programme Recording Aerial Pin AV input Connector ScartSatellite Receiver Unit TV Aerial cableAccess Mode SET Screen Access Main Menu ScreenSelect L-2 Select Mode Engage Auto Satellite Prog REC ModeAdjust Tracking Playback Picture AdjustmentOverride Automatic Tracking ManuallyAccess Mode SET Screen Access Main Menu ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Edit To Or From Another Video Recorder Input ModeSET Recording DECK’S Start Source PlayerOff. pg Select SettingTo the AV2 L-2 IN/DECODER connector On-Screen Display ENABLE/DISABLE ON-SCREEN DisplayOther Functions Power SAVE, then press Power Save ModeNext Function Memory Auto TimerAuto SP→LP Timer Activate Repeat Playback Repeat PlaybackNtsc Playback Audio Cable not provided Speaker Connection To a StereoJust Clock Clock SetGuide Program Number Set Video Plus+ SetupNumber Exit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Perform Auto Channel SET Tuner SetAuto Channel Set CH SETProcedures Screen preset positionsAfter Scan Completed Is displayed on the screenSelect Band Storing Channels ManuallyInput Channel Enter NEW Channel InformationChange Station Preset Position When Receiving a Scrambled BroadcastFine-Tuning Channels Already Stored Delete a ChannelSwitch Stations Access ManualChannel SET Screen Select NEW StationTV Station And ID List TV Station Channel Number Guide What happens if the tape runs out during recording? Questions And AnswersÄ remain lit on the display panel. Is there Problem? Troubleshooting Won’t stop Timer RecordingFront View IndexProgramme Time Indicators show the programme AV1 L-1 IN/OUT Connector enables AV connecTape Remaining Time Indicator displays time remaining Record PauseRemote Control VCR, TV PR +/-,TV +/-, TV Muting Fast Forward FF Button fast-forwards tapeDA4 Double Azimuth helical Maximum recording timeRotary two-head herical scan VHF 44.5 143/143 470 MHz
Top Page Image Contents