JVC HR-S7955EK manual Advanced features

Page 49

advanced features

49

programme satellite receiver Enter the details of the programme into your satellite receiver (see receiver manual) and put a tape in the VCR.

get to the output/input set screen Press m. Move the highlight bar to OUTPUT/INPUT

SET using the Aand Bbuttons and press

3

OK /

(or E).

 

 

 

select l-2 select mode Move the highlight bar to L-2 SELECT using the Aand B

buttons. Press

3

OK /

(or E) to select A/V or SAT. Then press m.

 

 

 

set tape speed Press /on the Remote Control to set the tape speed to either SP, LP or EP.

engage vcr in auto mode Press and hold SATcon the VCR for about 2 seconds. The indicator on the VCR display panel lights up and the VCR turns off automatically. Any signal detected at the AV2 (L-2) IN/DECODER connecter will automatically start the VCR recording; when the signal stops, so will the VCR.

Notes

connectors Auto Satellite Prog Recording is only possible using the AV2 (L-2) IN/DECODER connector.

timer mode You cannot put the VCR into TIMER MODE when using Auto Satellite Prog Recording Mode.

rThe number of programmes recorded will not be displayed on the VCR display panel when the rbutton is pressed.

timer recording Auto Satellite Prog Recording is not possible if your satellite receiver does not have a timer.

indicator The indicator light flashes when Auto Satellite Prog Recording is in progress.

disengage To disengage the VCR during Auto Satellite Prog Recording, press the obutton. The VCR will stop recording and turns off.

tape speed When recording two or more programmes consecutively, you cannot set a different tape speed for each programme. The first speed selected will apply to all programmes in that recording session.

b.e.s.t. The B.E.S.T. system will not work during Auto Satellite Prog Recording.

just clock Just Clock does not work when in Auto Satellite Prog Recording mode.

incoming signal The VCR will only react to the start of an incoming signal at the AV2 (L-2) IN/DECODER connecter. If you try to engage Auto Satellite Prog Recording Mode whilst the satellite receiver is powered on, the indicator will flash but the VCR will not record. You must power the satellite receiver off then on again to begin recording in these circumstances.

cable input You can record in the same way from a cable system as long as you connect the cable system has a timer on/off function and is connected to the AV2 (L-2) IN/DECODER connector.

incompatibilities Some satellite receivers output signals even when turned off. These receiv- ers cannot be used with this VCR in this way.

Page 48 Page 50
Image 49
Page 48 Page 50
Contents HR-S7955EK Blue to N Neutral or Black Brown to L Live or Red Safety PrecautionsMoisture Condensation On The Safe Use Of Equipment Some Do’s And Don’tsContents Display Remote control Front Panel Diagram KeyGetting Everything Ready Welcome to JVCPerform Auto Setup  pg Video Connection Three-Step Quick Start Auto SetupIs vacant and have set the VCR to Consult your local JVC dealerPress Preset DownloadOr E Finish Off Check the ResultsGo straight to 2000 used as example only Perform Clock Set on Go to StepWelcome to jvc Basic Features Load a Video Cassette PlaybackPlay Stop & EjectRewind and Fast Forward Video Heads CleaningAdvanced JOG Dial Playback FeaturesPause During Playback Single Frame MovementHigh Speed Search Variable Speed SearchYou can use variable speed search with one of two methods NormalChoose a Programme RecordingSet the Tape Speed Start RecordingDisplay Tape Remaining Time Check Elapsed Recording Time and Reset ItChange Display Information Recording Resume Function Instant Timer RecordingGet to the Video Plus + Screen Video Plus + Timer ProgrammingEnter the PlusCode Number Make sure that the preset number displayed is Programme stop time, then the date and presetDelayed, your VCR will still record it properly Leave the satellite receiver’s power onEdit Programme Title Engage Timer ModeReturn to Normal Screen Get to the Programme Screen Express Timer ProgrammingEnter Programme Details Press pthen press Start + Display panel looks like thisPress the number key 24H Express Timer Programming Press c, then press oto disengage the timer mode Check, Cancel & Change ProgrammesEdit programme title Press the number key Then press When Programmes Overlap Each OtherAdvanced Features Manual Tracking Picture QualityDigital 3R Digital TBC/NRPicture Control Video StabilizerSuper VHS ET S-VHS ET Tape TypeYour VCR can record in S-VHS, S-VHS ET or VHS Super VHS S-VHS, S-VHS ET and VHSSee ‘Super VHS ET S-VHS ET’ on Avoiding B.E.S.T. Time Delay Recording and Playback Using B.E.S.TTurning B.E.S.T. on or OFF Nicam Stereo and Bilingual Broadcasts Sound ModesSoundtrack Selection Skip Search Finding Specific ScenesIndex Search Instant ReViewIf the VCR cannot detect the tape information, ‘NO Tape Programme NavigationTurn Off Navigation Navigation PlaybackPress the number key 1. The Title Edit screen appears Entering CharacterEnter programme title Press the number keys and Eto Character’ belowDelete Tape Data You can use your TV’s Remote Control to turn off the VCR TV Auto Power OnLink Functions NexTView LinkHighlight bar to Mode SET using the Aand Bbuttons and pressDirect Rec Recording onInstalling Satellite Controller Satellite Receiver Control SettingsSET using the Aand Bbuttons. Press Or E Setting satellite receiver’s brandAfter pressing Mode Appropriate number keys to enter the brandCheck Result of Test Or E to finish the Sat Control Set modePress the Aand Bbuttons to move Auto Record from Satellite Receiver Auto SatelliteAdvanced features Desired mode OUTPUT/INPUT SettingEditing Buttons. Press OK / or E to selectFor L-2 Select SELECT/INPUT SettingSet edit mode See Picture Control on Editing Using Another VCRYour VCR as the Player Editing from a Camcorder On-Screen Display O.S.D Other FunctionsAuto SP aLP Timer Power Save ModeAuto Power Off/3H Auto TimerRepeat Playback Next Function MemoryAUX in or Tape Monitor Connection to a Stereo SystemExit Video Channel Set Mode Access Video Channel ModeVideo Channel Set Set Video ChannelMark on the screen moves Auto Channel SetupPress Or E Manual Channel SetupDelete a Channel Change Station NameButton on the Remote Control until the item you want to Change Station Preset PositionTV Station ID Guide Fine-Tuning Stored ChannelsBBC1 BBC2 ITV CH4 CH5 TV Station Channel Number GuideOr E. The date Setting the ClockOr E. Set the correct year Guide Program Numbers Manually Setting Guide Program NumbersQuestion and Answers Uand cremain lit on the display panel. Is there a problem?Can the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?Symptom Possible Cause TroubleshootingRecording Other Problems Record a Programme While Watching Another 424Memo Memo Memo HR-S7955EK
Top Page Image Contents