JVC HR-S7955EK manual Other Problems

Page 71

subsidiary information

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

71

TIMER RECORDING (cont.)

 

5. cblinks for 10 seconds and the

chas been pressed when

Timer mode is disengaged.

there are no programs in

 

memory, or the timer record

 

information has been pro-

 

grammed incorrectly.

Check the programmed data and re-programme as necessary, then press cagain.

6.The VIDEO Plus+ system does not timer record properly.

7.U, ,and the indicator won’t stop blinking.

The VCR’s preset positions have been set incorrectly.

The loaded cassette has had its record safety tab removed.

Refer to Guide Program Numbers (pg. 56) and re-perform the procedure.

Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact.

The end of the tape was reached during Auto Satellite Programme Recording.

The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

8. Uand ,on the display panel

• The end of the tape was

won’t stop blinking.

reached during Instant Timer

 

Recording.

The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

OTHER PROBLEMS

1.Whistling or howling is heard from the TV during camcorder recording.

2.When scanning channels, some of them are skipped over.

3.The preset cannot be changed.

4.Channel settings that were made manually seem to have changed or disappeared.

5.No channels are stored in the VCR’s memory.

The camcorder’s microphone is too close to the TV.

The TV’s volume is too high.

Those channels have been designated to be skipped.

Recording is in progress.

After the manual settings were made, Auto Channel Set was performed.

The TV aerial cable was not connected to the VCR when Auto Set Up was performed.

The fully-wired 21-pin SCART cable was not connected between TV and the VCR when Preset Download was per- formed.

Position the camcorder so its microphone is away from the TV. Turn the TV’s volume down.

If you need the skipped channels, restore them.

Press to pause the recording, change presets, then press .to resume recording.

Perform manual setting again.

Turn off the VCR once and connect the TV aerial cable to the VCR properly, then turn on the VCR again. Then perform Auto Setup again (pg. 11).

Turn off the VCR once and connect the fully-wired 21-pin SCART cable to the VCR properly, then turn on the VCR again. Then perform Preset Download again

(pg. 12).

Image 71
Contents HR-S7955EK Blue to N Neutral or Black Brown to L Live or Red Safety PrecautionsMoisture Condensation On The Safe Use Of Equipment Some Do’s And Don’tsContents Display Remote control Front Panel Diagram KeyGetting Everything Ready Welcome to JVCPerform Auto Setup  pg Video Connection Consult your local JVC dealer Auto SetupThree-Step Quick Start Is vacant and have set the VCR toOr E Preset DownloadPress Perform Clock Set on Go to Step Check the ResultsFinish Off Go straight to 2000 used as example onlyWelcome to jvc Basic Features Stop & Eject PlaybackLoad a Video Cassette PlayRewind and Fast Forward Video Heads CleaningSingle Frame Movement Playback FeaturesAdvanced JOG Dial Pause During PlaybackNormal Variable Speed SearchHigh Speed Search You can use variable speed search with one of two methodsStart Recording RecordingChoose a Programme Set the Tape SpeedChange Display Information Check Elapsed Recording Time and Reset ItDisplay Tape Remaining Time Recording Resume Function Instant Timer RecordingEnter the PlusCode Number Video Plus + Timer ProgrammingGet to the Video Plus + Screen Leave the satellite receiver’s power on Programme stop time, then the date and presetMake sure that the preset number displayed is Delayed, your VCR will still record it properlyReturn to Normal Screen Engage Timer ModeEdit Programme Title Press pthen press Start + Display panel looks like this Express Timer ProgrammingGet to the Programme Screen Enter Programme DetailsPress the number key 24H Express Timer Programming Edit programme title Press the number key Check, Cancel & Change ProgrammesPress c, then press oto disengage the timer mode Then press When Programmes Overlap Each OtherAdvanced Features Digital TBC/NR Picture QualityManual Tracking Digital 3RPicture Control Video StabilizerSuper VHS ET S-VHS ET Tape TypeSee ‘Super VHS ET S-VHS ET’ on Super VHS S-VHS, S-VHS ET and VHSYour VCR can record in S-VHS, S-VHS ET or VHS Turning B.E.S.T. on or OFF Recording and Playback Using B.E.S.TAvoiding B.E.S.T. Time Delay Soundtrack Selection Sound ModesNicam Stereo and Bilingual Broadcasts Instant ReView Finding Specific ScenesSkip Search Index SearchIf the VCR cannot detect the tape information, ‘NO Tape Programme NavigationTurn Off Navigation Navigation PlaybackCharacter’ below Entering CharacterPress the number key 1. The Title Edit screen appears Enter programme title Press the number keys and EtoDelete Tape Data NexTView Link TV Auto Power OnYou can use your TV’s Remote Control to turn off the VCR Link FunctionsRecording on SET using the Aand Bbuttons and pressHighlight bar to Mode Direct RecInstalling Satellite Controller Satellite Receiver Control SettingsAppropriate number keys to enter the brand Setting satellite receiver’s brandSET using the Aand Bbuttons. Press Or E After pressing ModePress the Aand Bbuttons to move Or E to finish the Sat Control Set modeCheck Result of Test Auto Record from Satellite Receiver Auto SatelliteAdvanced features Buttons. Press OK / or E to select OUTPUT/INPUT SettingDesired mode EditingFor L-2 Select SELECT/INPUT SettingSet edit mode See Picture Control on Editing Using Another VCRYour VCR as the Player Editing from a Camcorder On-Screen Display O.S.D Other FunctionsAuto SP aLP Timer Power Save ModeNext Function Memory Auto TimerAuto Power Off/3H Repeat PlaybackAUX in or Tape Monitor Connection to a Stereo SystemSet Video Channel Access Video Channel ModeExit Video Channel Set Mode Video Channel SetMark on the screen moves Auto Channel SetupPress Or E Manual Channel SetupDelete a Channel Change Station NameButton on the Remote Control until the item you want to Change Station Preset PositionTV Station ID Guide Fine-Tuning Stored ChannelsBBC1 BBC2 ITV CH4 CH5 TV Station Channel Number GuideOr E. Set the correct year Setting the ClockOr E. The date Guide Program Numbers Manually Setting Guide Program NumbersCan the VCR indefinitely remain in the Record-Pause mode? Uand cremain lit on the display panel. Is there a problem?Question and Answers Can the VCR indefinitely remain in the still mode?Symptom Possible Cause TroubleshootingRecording Other Problems Record a Programme While Watching Another 424Memo Memo Memo HR-S7955EK