JVC RX-774RBK manual TV as the sound source or DBS tuner connection, To audio output DBS tuner

Page 22

Getting Started

English

TV (as the sound source) or DBS tuner connection

You can connect either the TV or DBS tuner to the TV SOUND/DBS jacks.

Note:

RIGHT	LEFT AUDIO
GND	PHONO
	CD
To audio output	OUT
	(REC)
	TAPE
	/MD
	IN
	(PLAY)
	CENTER
SUB	DVD
WOOFER	DVD

RIGHT

LEFT

VIDEO

S-VIDEO

DVD

TV SOUND

/DBS

OUT

(REC)

VCR

(PLAY)

When connecting the TV to the TV SOUND/DBS jacks, DO NOT connect the TV’s video output to the video input terminal of the TV SOUND/DBS jacks.

SUBWOOFER	MONITOR
OUT	OUT

GND

To audio output

DBS tuner

DBS

RIGHT

LEFT

AUDIO

PHONO

OUT

(REC)

TAPE

/MD

(PLAY)

CENTER

SUB

WOOFERDVD

RIGHT

LEFT

VIDEO

S-VIDEO

DVD

TV SOUND

/DBS

OUT

(REC)

VCR

(PLAY)

Note:

When connecting the DBS tuner to the TV SOUND/DBS jacks, change the source name, which will be shown on the display when selected as the source, to “DBS.” See page 23 for details.

SUBWOOFER	MONITOR
OUT	OUT

To video output

Image 22

Contents RX-774RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-774RBK Table of Contents Using the DSP Modes Selecting Your Favorite SEA Mode Creating Your Own SEA Mode3 4 5 6 78 9 0-= Parts IdentificationFront Panel To use the Multi JOG control ª on the front panelRemote Control When using the remote controlEasy Set Up & Operations RX-774RBKTurn on the power Select the source Easy Set Up & Operations For Reproducing DVD Multi playback with your DVD playerMulti Phono Locations Getting StartedGeneral Handling the receiverUsing the Standard Type Connector Not Supplied Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna FM Antenna ConnectionsConnecting the Speakers Connecting the front speakersGetting Started Connecting the rear and center speakers Connecting the subwoofer speakerCase 2 When you connect two sets of front speakers Case 1 When you connect only one set of front speakersAbout the speaker impedance Audio component connections Connecting Audio/Video ComponentsAudio Components Video Components Video component connections TV connection as the monitorWhen you connect the DVD player with stereo output jacks DVD player connectionTV as the sound source or DBS tuner connection To audio output DBS tunerVCR connection InputPress Power to set it in the Ñoff position Connecting the Power CordTo shut off the power completely Putting Batteries in the Remote ControlBasic Operations From the remote controlTurning the Power On and Off Standby On the front panelBasic Operations Adjusting the VolumeTo increase the volume, turn Master Volume Press one of the source selecting buttons directlyListening only with headphones From the remote control onlyOn the front panel only Listening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance Changing the Source NameTo cancel the Sleep Timer Using the Sleep TimerWhen the shut-off time comes Setting Center and Rear Speakers for DSP ModesSelect this mode when you use rear speakers Basic SettingsRear Speaker Setting Select this mode when you do not use rear speakersTo cancel the One Touch Operation function To store the sound settingsTo recall the sound settings One Touch OperationTo store the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsTo erase a stored preset station To tune in a preset stationPress FM MODE/MUTE to select the FM reception mode Selecting the FM Reception ModePress FM Mode to select the FM reception mode Receiving Radio BroadcastsPress Tuner PRESET, while a character you want is flashing Assigning Names to Preset StationsTune in a preset station. See page 28 for details Character is flashing after you have assigned a nameWhat Information Can RDS Signals Provide? Using the RDS Radio Data System to Receive FM StationsTo show the RDS signals To continue searching after the first stop To search for a program using the PTY codesSearching for a Program by PTY Codes To stop searching any time during the processStation Press PTY Search while listening to an FMDescriptions of the PTY codes Traffic Announcement in your area Switching to a Broadcast Program of Your Choice TemporarilyReceiver enters EON standby mode NewsTo stop listening to the program selected by EON Selecting Your Favorite SEA Mode Using the SEA ModesTo cancel the SEA mode To recall your own SEA adjustment Using the SEA ModesCreating Your Own SEA Mode To erase a stored adjustmentOn the DAP mode Using the DSP ModesOn 3D-PHONIC mode On Surround modePress DSP Mode Using the DSP ModesUsing the 3D-PHONIC Modes Press BALANCE/SURROUND Adjust repeatedlyPress Sound Control To cancel the 3D-PHONIC modeKeys are activated for sound adjustments Press Effect to select the effect levelGives the feeling of a live music club with a low ceiling Using the DAP ModesNo DSP mode is applied Gives a throbbing bass beatTo cancel the DAP mode Press Rearl +/- to adjust the rear speaker output level Each time you press the button, the effect level changesPreparing for Surround Modes No DSP mode is applied For the other modes, see pages 39Press Test to start checking the speaker output balance Center tone adjustment affects the mid-frequency If necessary, adjust the speaker output level as followsAdjusted level are also shown on the equalizer display For Dolby Pro Logic Center tone cannot be To cancel the Surround mode Using Surround ModesPress Surround Mode repeatedly until OFF appears Activating the DVD Multi Playback Using the DVD Multi Playback ModeSpeaker Arrangements for DVD Multi Playback Refer to the manual supplied with the DVD playerSOFT2 SOFT1 Flat SHARP1 SHARP2 Press Cntr +/- to adjust the center speaker output level Using the DVD Multi Playback ModeKeys are activated for adjusting the sound Press DVD Multi so that DVD Multi appears on the displaySelecting the Source to Play Also see Using the On-Screen MenusWhen you select OSD, see Selecting the Different Sources for Picture and SoundListening at Low Volume Loudness Also see Using the On-Screen MenusAdjusting the Front Speaker Output Balance Also see Sound Control menu appearsSelecting Your Favorite SEA Mode Also see Setting the Center Speaker Size Also see Creating Your Own SEA Mode Also seePress SET to store the setting into the SEA Usermode Setting the Delay Time Also see Setting the Rear Speaker Also seeOperating the Tuner Preset Memory menu appears Storing the Preset Stations Also seeAssigning Names to the Preset Stations Also see Character entry screen appearsChecking the RDS Information Also see RDS Information menu appearsAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingDisplaying the Disc Information on the TV screen Text Compu Link Remote Control SystemPlugs not supplied with this receiver Disc Search Only for CD PlayerText Compu Link Remote Control System Showing the Disc Information on the TV ScreenPress SET again Searching a Disc Only for the CD playerSearch a disc by its performer Going back to the Performer Search screen Press ExitPress on Screen Control %/ Þto move to GENRE, then press Going back to the Disc Title Search screen Press ExitSearch a disc by its genre Genre Search screen appearsUser File screen appears on the TV Using your own User FilesGoing back to the User File screen Press Exit Title Input Performer screen appears on the TV Entering the Disc InformationFor the CD Player with the disc memory function To move to Shift , then press SETEnter the title, referring to steps 3 and 4 on For the MD recorderEnter the song title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components Play Starts playing Stop Stops playing CD player-changerTurntable Cassette deckOperating JVC’s Audio/Video Components Following buttons can be used for operating the TV Sets the input mode either TVVCRmode selector is set to the correct position Turns on and off TVOperating Other Manufactures’ Components 10, 0, 100++10Starts recording or enters recording Starts playbackPauses PauseManufacturers’ codes for TV Manufacturers’ codes for Catv converters Manufacturers’ codes for VCR Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierVideo EN, GE, FR, NL, SP, IT 0498OFMMDWJEM