JVC RX-774RBK manual Using the SEA Modes, Selecting Your Favorite SEA Mode, To cancel the SEA mode

Page 41

Using the SEA Modes

The SEA (Sound Effect Amplifier) modes give you control of the way your music sounds.

English

				IMPORTANT:
		AUDIO/TV		When using the Remote Control, check to see if its remote control
		/VCR		mode selector is set to the correct position:


		/DBS		To operate this receiver, set it to “AUDIO/TV/VCR (except when
		CATV
				selecting the DBS tuner as the source).”


Selecting Your Favorite SEA Mode
On the front panel:					SEA MODE
On the front panel:

1. Press SEA MODE.

The display changes to show the current setting.

2. Turn MULTI JOG until the mode you want appears	MULTI JOG
2. Turn MULTI JOG until the mode you want appears
on the display, while the indication of the previous
step is still on the display.

As you turn it, the SEA mode changes as follows:

SEA ROCKSEA MUSICALSEA MOVIESEA COUNTRY

			SEA OFF			SEA USERMODE		SEA JAZZ
			SEA OFF			SEA USERMODE		SEA JAZZ

		SEA ROCK:				Gives a heavy sound. Both high and low frequencies are
						boosted.
		SEA MUSICAL:				Enhance the mid-frequency range, which the human
						voice is mostly made up of.
		SEA MOVIE:				Adds breadth to sounds so you feel like you are in a
						movie theater.
		SEA COUNTRY:				Enhances the high-frequency range so that instruments
						such the violin and banjo are emphasized.

		SEA JAZZ:				Gives a feeling of a live atmosphere. Good for acoustic
						music.
		SEA USERMODE:				Your original SEA adjustment (see page 37).

		SEA OFF:				No SEA mode is applied (see below).

To cancel the SEA mode
Turn MULTI JOG until “SEA OFF” appears in step 2 above.
The SEA indicator goes off from the display.
From the remote control:
Press SEA MODE repeatedly until the SEA mode you										SEA
Press SEA MODE repeatedly until the SEA mode you										MODE

want appears on the display.

Each time you press the button, the SEA mode changes as follows:

SEA ROCKSEA MUSICALSEA MOVIE SEA COUNTRY

SEA OFF SEA USERMODE SEA JAZZ

To cancel the SEA mode

Press SEA MODE repeatedly until “SEA OFF” appears.

The SEA indicator goes off from the display.

Notes:

•The SEA modes cannot be used for recording.

•When the SEA mode is turned on, the SEA indicator lights up on the display.

Note:

When the SEA mode is turned on, the SEA indicator lights up on the display.

36

Image 41

Contents RX-774RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-774RBK Table of Contents Selecting Your Favorite SEA Mode Creating Your Own SEA Mode Using the DSP ModesFront Panel Parts Identification3 4 5 6 78 9 0-= To use the Multi JOG control ª on the front panelWhen using the remote control Remote ControlRX-774RBK Easy Set Up & OperationsTurn on the power Select the source For Reproducing DVD Multi playback with your DVD player Easy Set Up & OperationsMulti Phono General Getting StartedLocations Handling the receiverUsing the Supplied FM Antenna Connecting the FM and AM MW/LW AntennasUsing the Standard Type Connector Not Supplied FM Antenna ConnectionsGetting Started Connecting the front speakersConnecting the Speakers Connecting the subwoofer speaker Connecting the rear and center speakersAbout the speaker impedance Case 1 When you connect only one set of front speakersCase 2 When you connect two sets of front speakers Audio Components Video Components Connecting Audio/Video ComponentsAudio component connections TV connection as the monitor Video component connectionsDVD player connection When you connect the DVD player with stereo output jacksTo audio output DBS tuner TV as the sound source or DBS tuner connectionInput VCR connectionTo shut off the power completely Connecting the Power CordPress Power to set it in the Ñoff position Putting Batteries in the Remote ControlTurning the Power On and Off Standby From the remote controlBasic Operations On the front panelTo increase the volume, turn Master Volume Adjusting the VolumeBasic Operations Press one of the source selecting buttons directlyOn the front panel only From the remote control onlyListening only with headphones Adjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness Changing the Source NameWhen the shut-off time comes Using the Sleep TimerTo cancel the Sleep Timer Setting Center and Rear Speakers for DSP ModesRear Speaker Setting Basic SettingsSelect this mode when you use rear speakers Select this mode when you do not use rear speakersTo recall the sound settings To store the sound settingsTo cancel the One Touch Operation function One Touch OperationUsing Preset Tuning Tuning in Stations ManuallyTo store the preset stations Receiving Radio BroadcastsTo tune in a preset station To erase a stored preset stationPress FM Mode to select the FM reception mode Selecting the FM Reception ModePress FM MODE/MUTE to select the FM reception mode Receiving Radio BroadcastsTune in a preset station. See page 28 for details Assigning Names to Preset StationsPress Tuner PRESET, while a character you want is flashing Character is flashing after you have assigned a nameTo show the RDS signals Using the RDS Radio Data System to Receive FM StationsWhat Information Can RDS Signals Provide? Searching for a Program by PTY Codes To search for a program using the PTY codesTo continue searching after the first stop To stop searching any time during the processDescriptions of the PTY codes Press PTY Search while listening to an FMStation Receiver enters EON standby mode Switching to a Broadcast Program of Your Choice TemporarilyTraffic Announcement in your area NewsTo stop listening to the program selected by EON To cancel the SEA mode Using the SEA ModesSelecting Your Favorite SEA Mode Creating Your Own SEA Mode Using the SEA ModesTo recall your own SEA adjustment To erase a stored adjustmentOn 3D-PHONIC mode Using the DSP ModesOn the DAP mode On Surround modeUsing the 3D-PHONIC Modes Using the DSP ModesPress DSP Mode Press BALANCE/SURROUND Adjust repeatedlyKeys are activated for sound adjustments To cancel the 3D-PHONIC modePress Sound Control Press Effect to select the effect levelNo DSP mode is applied Using the DAP ModesGives the feeling of a live music club with a low ceiling Gives a throbbing bass beatTo cancel the DAP mode Each time you press the button, the effect level changes Press Rearl +/- to adjust the rear speaker output levelPress Test to start checking the speaker output balance No DSP mode is applied For the other modes, see pages 39Preparing for Surround Modes Adjusted level are also shown on the equalizer display If necessary, adjust the speaker output level as followsCenter tone adjustment affects the mid-frequency For Dolby Pro Logic Center tone cannot be Press Surround Mode repeatedly until OFF appears Using Surround ModesTo cancel the Surround mode Speaker Arrangements for DVD Multi Playback Using the DVD Multi Playback ModeActivating the DVD Multi Playback Refer to the manual supplied with the DVD playerSOFT2 SOFT1 Flat SHARP1 SHARP2 Keys are activated for adjusting the sound Using the DVD Multi Playback ModePress Cntr +/- to adjust the center speaker output level Press DVD Multi so that DVD Multi appears on the displayWhen you select OSD, see Using the On-Screen MenusSelecting the Source to Play Also see Selecting the Different Sources for Picture and SoundAdjusting the Front Speaker Output Balance Also see Using the On-Screen MenusListening at Low Volume Loudness Also see Sound Control menu appearsSelecting Your Favorite SEA Mode Also see Press SET to store the setting into the SEA Usermode Creating Your Own SEA Mode Also seeSetting the Center Speaker Size Also see Operating the Tuner Setting the Rear Speaker Also seeSetting the Delay Time Also see Assigning Names to the Preset Stations Also see Storing the Preset Stations Also seePreset Memory menu appears Character entry screen appearsRDS Information menu appears Checking the RDS Information Also seeRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingPlugs not supplied with this receiver Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerShowing the Disc Information on the TV Screen Text Compu Link Remote Control SystemSearch a disc by its performer Searching a Disc Only for the CD playerPress SET again Going back to the Performer Search screen Press ExitSearch a disc by its genre Going back to the Disc Title Search screen Press ExitPress on Screen Control %/ Þto move to GENRE, then press Genre Search screen appearsGoing back to the User File screen Press Exit Using your own User FilesUser File screen appears on the TV For the CD Player with the disc memory function Entering the Disc InformationTitle Input Performer screen appears on the TV To move to Shift , then press SETEnter the song title, referring to steps 3 and 4 on For the MD recorderEnter the title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components Turntable CD player-changerPlay Starts playing Stop Stops playing Cassette deckOperating JVC’s Audio/Video Components VCRmode selector is set to the correct position Sets the input mode either TVFollowing buttons can be used for operating the TV Turns on and off TV10, 0, 100++10 Operating Other Manufactures’ ComponentsPauses Starts playbackStarts recording or enters recording PauseManufacturers’ codes for TV Manufacturers’ codes for Catv converters Manufacturers’ codes for VCR Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsVideo EN, GE, FR, NL, SP, IT 0498OFMMDWJEM