JVC RX-774RBK manual To stop listening to the program selected by EON

Page 40

Receiving Radio Broadcasts

English

CASE 2 If there is a station broadcasting the program you have selected

The receiver changes the source (all sources except AM (MW/LW)), and tunes in the station. The indicator of received PTY code starts flashing.

Ô

When the program is over, the receiver goes back to the previously selected source, but still remains in EON standby mode. The indicator of received PTY code stops flashing and remains lit.

CASE 3 If the FM station you are listening is broadcasting the program you have selected

The receiver continues to receive the station but the indicator of received PTY code starts flashing.

Ô

When the program is over, the indicator of received PTY code stops flashing and remains lit, but the receiver remains in EON standby mode.

To stop listening to the program selected by EON

Press EON so that the program type (TA/NEWS/INFO) goes off from the display. The receiver enters EON off mode and goes back to the previously selected source.

Each time you press EON, the EON mode alternates between standby mode and off mode.

Notes:

•EON data sent from some stations may not be compatible with this receiver.

•In EON standby mode, if you change the source to AM (MW/LW) or if you carry out synchronized recording (see page 59), EON standby mode is canceled temporarily. The receiver goes back to EON standby mode again when you have finished that operation.

•While listening to a program tuned in by the EON function, you can only use STANDBY/

ON , EON, MASTER VOLUME (on the front panel)

and AUDIO (on the remote control).

•While listening to a program tuned in by the EON function, you cannot perform the on- screen operations (pages 52 and 61).

•When the receiver is turned off (into standby mode), the EON function is also turned off.

CAUTION:

When the source alternates intermittently between the station tuned in by the EON function and the currently selected source, press EON to cancel the EON function. This is not a malfunction of the receiver.

35

Image 40

Contents RX-774RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-774RBK Table of Contents Using the DSP Modes Selecting Your Favorite SEA Mode Creating Your Own SEA ModeParts Identification Front Panel3 4 5 6 78 9 0-= To use the Multi JOG control ª on the front panelRemote Control When using the remote controlEasy Set Up & Operations RX-774RBKTurn on the power Select the source Easy Set Up & Operations For Reproducing DVD Multi playback with your DVD playerMulti Phono Getting Started GeneralLocations Handling the receiverConnecting the FM and AM MW/LW Antennas Using the Supplied FM AntennaUsing the Standard Type Connector Not Supplied FM Antenna ConnectionsConnecting the Speakers Connecting the front speakersGetting Started Connecting the rear and center speakers Connecting the subwoofer speakerCase 2 When you connect two sets of front speakers Case 1 When you connect only one set of front speakersAbout the speaker impedance Audio component connections Connecting Audio/Video ComponentsAudio Components Video Components Video component connections TV connection as the monitorWhen you connect the DVD player with stereo output jacks DVD player connectionTV as the sound source or DBS tuner connection To audio output DBS tunerVCR connection InputConnecting the Power Cord To shut off the power completelyPress Power to set it in the Ñoff position Putting Batteries in the Remote ControlFrom the remote control Turning the Power On and Off StandbyBasic Operations On the front panelAdjusting the Volume To increase the volume, turn Master VolumeBasic Operations Press one of the source selecting buttons directlyListening only with headphones From the remote control onlyOn the front panel only Basic Settings Adjusting the Front Speaker Output BalanceListening at Low Volume Loudness Changing the Source NameUsing the Sleep Timer When the shut-off time comesTo cancel the Sleep Timer Setting Center and Rear Speakers for DSP ModesBasic Settings Rear Speaker SettingSelect this mode when you use rear speakers Select this mode when you do not use rear speakersTo store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Using Preset TuningTo store the preset stations Receiving Radio BroadcastsTo erase a stored preset station To tune in a preset stationSelecting the FM Reception Mode Press FM Mode to select the FM reception modePress FM MODE/MUTE to select the FM reception mode Receiving Radio BroadcastsAssigning Names to Preset Stations Tune in a preset station. See page 28 for detailsPress Tuner PRESET, while a character you want is flashing Character is flashing after you have assigned a nameWhat Information Can RDS Signals Provide? Using the RDS Radio Data System to Receive FM StationsTo show the RDS signals To search for a program using the PTY codes Searching for a Program by PTY CodesTo continue searching after the first stop To stop searching any time during the processStation Press PTY Search while listening to an FMDescriptions of the PTY codes Switching to a Broadcast Program of Your Choice Temporarily Receiver enters EON standby modeTraffic Announcement in your area NewsTo stop listening to the program selected by EON Selecting Your Favorite SEA Mode Using the SEA ModesTo cancel the SEA mode Using the SEA Modes Creating Your Own SEA ModeTo recall your own SEA adjustment To erase a stored adjustmentUsing the DSP Modes On 3D-PHONIC modeOn the DAP mode On Surround modeUsing the DSP Modes Using the 3D-PHONIC ModesPress DSP Mode Press BALANCE/SURROUND Adjust repeatedlyTo cancel the 3D-PHONIC mode Keys are activated for sound adjustmentsPress Sound Control Press Effect to select the effect levelUsing the DAP Modes No DSP mode is appliedGives the feeling of a live music club with a low ceiling Gives a throbbing bass beatTo cancel the DAP mode Press Rearl +/- to adjust the rear speaker output level Each time you press the button, the effect level changesPreparing for Surround Modes No DSP mode is applied For the other modes, see pages 39Press Test to start checking the speaker output balance Center tone adjustment affects the mid-frequency If necessary, adjust the speaker output level as followsAdjusted level are also shown on the equalizer display For Dolby Pro Logic Center tone cannot be To cancel the Surround mode Using Surround ModesPress Surround Mode repeatedly until OFF appears Using the DVD Multi Playback Mode Speaker Arrangements for DVD Multi PlaybackActivating the DVD Multi Playback Refer to the manual supplied with the DVD playerSOFT2 SOFT1 Flat SHARP1 SHARP2 Using the DVD Multi Playback Mode Keys are activated for adjusting the soundPress Cntr +/- to adjust the center speaker output level Press DVD Multi so that DVD Multi appears on the displayUsing the On-Screen Menus When you select OSD, seeSelecting the Source to Play Also see Selecting the Different Sources for Picture and SoundUsing the On-Screen Menus Adjusting the Front Speaker Output Balance Also seeListening at Low Volume Loudness Also see Sound Control menu appearsSelecting Your Favorite SEA Mode Also see Setting the Center Speaker Size Also see Creating Your Own SEA Mode Also seePress SET to store the setting into the SEA Usermode Setting the Delay Time Also see Setting the Rear Speaker Also seeOperating the Tuner Storing the Preset Stations Also see Assigning Names to the Preset Stations Also seePreset Memory menu appears Character entry screen appearsChecking the RDS Information Also see RDS Information menu appearsCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingText Compu Link Remote Control System Plugs not supplied with this receiverDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerText Compu Link Remote Control System Showing the Disc Information on the TV ScreenSearching a Disc Only for the CD player Search a disc by its performerPress SET again Going back to the Performer Search screen Press ExitGoing back to the Disc Title Search screen Press Exit Search a disc by its genrePress on Screen Control %/ Þto move to GENRE, then press Genre Search screen appearsUser File screen appears on the TV Using your own User FilesGoing back to the User File screen Press Exit Entering the Disc Information For the CD Player with the disc memory functionTitle Input Performer screen appears on the TV To move to Shift , then press SETEnter the title, referring to steps 3 and 4 on For the MD recorderEnter the song title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components CD player-changer TurntablePlay Starts playing Stop Stops playing Cassette deckOperating JVC’s Audio/Video Components Sets the input mode either TV VCRmode selector is set to the correct positionFollowing buttons can be used for operating the TV Turns on and off TVOperating Other Manufactures’ Components 10, 0, 100++10Starts playback PausesStarts recording or enters recording PauseManufacturers’ codes for TV Manufacturers’ codes for Catv converters Manufacturers’ codes for VCR Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierVideo EN, GE, FR, NL, SP, IT 0498OFMMDWJEM