JVC HR-E249E specifications Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 8

8ENINITIALSETTINGS(cont.)

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

If you have connected the video recorder to your TV via the provided RF cable only (RF connection) – Go to "With RF Connection" below.

If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection) – Go to "With AV Connection" on next page.

IMPORTANT:

Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder.

	–
	.+/
TV	PROG
TV
	6		5/8
	q	1	Á

STOP

2

1 2 3

4

5

6

7 8 9

04

TV PROG.+/–

3

OK

1

TEST SIGNAL

The channel on which the screen to the left appear clearly in step 2 is your Video Channel.

With RF Connection

ACCESS VIDEO CHANNEL SET MODE

	Hold down STOP on the recorder until the display
1			panel shows the following.
1

2	SET VIDEO CHANNEL
	Set your TV to UHF channel 36.

	● If the two vertical white bars appear clearly on the
			screen as shown in the illustration at bottom left, go
			to step 3.
	● If the two vertical white bars do not appear clearly,
			press TV PROG.+ or – to set the video recorder to a
			vacant channel between 22 and 69 which is not
			occupied by any local station in your area.
		(Ex.) If channel 50 is available in your area

Then set your TV to UHF channel 50 and check if the two vertical white bars appear clearly on the screen; if so, go to step 3. If not, re-set the video recorder to another vacant channel and try again.

NOTES:

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to the Video Channel.

Image 8

Contents HR-E249E Do not place the recorder Safety PrecautionsFor Italy Check Contents Installing Your NEW Record ER ENBasic Connections Situate RecorderAuto Set Up Turn on the RecorderSelect Country EN I Nitial Sett IngsPerform Auto SET UP Select LanguageIf you are referring to On-screen displayInitial Settings If both auto channel set and auto clock set have failedLanguage for the on-screen display Just ClockLanguage Access Video Channel SET Mode Exit Video Channel SET ModeEN Initial Settings Video Channel SetAccess Video Channel SET ModeMode With AV ConnectionGuide Program Number Set SetupMake List of Stored Station Names Channel Positions When Using a Satellite Tuner Enter Showview NumberConfirm Channel Position Number Close MenuBasic PlaybackPlayback Features Pause During PlaybackStill Picture/Frame-By-Frame Playback Variable-Speed SearchAdjust Tracking Activate HIGH-SPEED SearchOverride Automatic Tracking ManuallyPlayback Activate 3R PictureActivate Repeat Tape Position Indicator Activate Index SearchActivate Instant Review Index SearchSET A/B Code Switch RE-SUPPLY PowerActivate Scene Finder Stop Scene FinderBasic Recording Access Main Menu ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays ScreenS.T. Picture System EN RecordingRecording Display Panel IndicationPlayback AuseRecording Features Reset CounterSelect Channel to Watch SET Counter DisplaySET Recording Duration Engage ITR ModeInstant Timer Recording ITR Timer Recording EN Timer RECORDINGcontWhen Using The Illumi-Guide Feature Press ProgPressing PROG. Check Program ScreenSatellite Tuner Users Regular Timer Programming Stop +/-,DATE +/-,TV PROG. +/-,MENUTV PROG. +/- and Menu Press TV PROG. +Access Programme Access Main Menu ScreenEN Timer Recording Revise ProgrammeTimer Warning PDC/VPS RecordingSET Recording DECK’S Input Mode Edit To Or From Another Video RecorderMake Connections Start Source PlayerPlayer RecorderEdit From a Camcorder SET RECORDER’S InputStart Camcorder Start RecorderConnecting Using a Decoder Select Input ModeConnect Decoder SET TunerTV Multi Brand Remote Control Control Your TV Using Additional ButtonsSET TV Brand Code TRY Operating TVTRY Operating Satellite Tuner Satellite Tuner MultiSET Satellite Tuner Brand Code Tuner SET Auto Channel SetPointer to your countrys Name, then press OK.SET Select Item Delete ChannelClose Confirmation Select NEW PositionSwitch Stations Access Manual CH. SETPerform Tuning Select NEW StationTV Station And ID List Station NameClock SET PreparationMove the highlight bar pointer to Clock SET by Screen appearsSET Clock Automatically Return to Normal ScreenSET Date and Time SET Just ClockTroubleshooting E N PowerTimer again OubleshootingÄ remain lit on the display panel. Is there a problem? Questions and Answer S E NIndex Front ViewRear View EN Index Installing BatteriesHow To Use Specifications GeneralEMO Memo Language Code HR-E249EInternational Telephone Country Code