Setting the VCR Setup Menu, Channel Selection

The TUNING menu will appear.

Press V to choose the SOURCE SELECT option, then press b/B to select TUNER.

press OK.

Setting the VCR Setup Menu

1	Press SYSTEM MENU and the MAIN menu will
	appear.
2	Press v/V to select the SETUP menu, then press
	OK.

The SETUP menu will appear.

3 Press v/V to choose a desired option on the SETUP menu. Then press b/B to choose a desired setting.

FUNCTION OSD

The on-screen display of this DVD+VCR can be turned on or off.

∀FUNCTION OSD can be switched between ON and OFF by pressing b/B.

AUDIO MODE

The DVD+VCR has two separate audio playback systems, the high quality VHS Hi-Fi system and standard NORMAL mono system. The same audio is generally recorded on both systems. The VHS Hi-Fi system plays on separate (Left and Right) channels, and the NOR- MAL system plays monaural sound. The normal track is always played so the cassette can be played on a DVD+VCR that does not have VHS Hi-Fi.

∀AUDIO MODE can be switched between HI-FI and NORMAL by pressing b/B.

BROADCAST TYPE (STEREO/SAP/MONO)

Multichannel Television Sound (MTS) carries stereo and/or Second Audio Program (SAP) bilingual signals. Set this display to the desired position when both MTS stereo and SAP signals are received. When only one MTS signal is received, the DVD+VCR automatically selects the corresponding receiving mode (Stereo or SAP) regardless of the selected position. For normal operation, the display should be in the STEREO position. The DVD+VCR will then record a STEREO program when available, and record a mono program IF the program is NOT IN STEREO.

For weak STEREO and/or SAP broadcasts, changing the display to mono may give clearer sound.

∀BROADCAST TYPE can be switched between STEREO, SAP, and MONO by pressing b/B.

AUDIO OUTPUT (STEREO/LEFT/RIGHT)

Used during playback [when AUDIO MODE-HI-FI/NORMAL is in HI-FI position] for selecting the audio output signals from the AUDIO OUT terminals (L ch and R ch), and RF.OUT.

This display setting should normally be left in the stereo position, so that when a stereo tape is played, the stereo sound will be heard through the left and right channels. If a mono tape is played and the audio output is set to stereo, the same mono sound will be heard from both left and right channels.

∀ AUDIO OUTPUT can be switched between STEREO, LEFT, and RIGHT by pressing b/B.

4 Press SYSTEM MENU when finished.

Getting Started 15

Channel Selection

This DVD+VCR is equipped with a frequency synthesized tuner capable of receiving up to 181 channels. These include VHF channels 2-13, UHF channels 14-69 and CATV channels 1-125.

Preparation:

∀Connect the DVD+VCR to the desired type of antenna or cable TV system, as shown in Connecting Antenna/Cable TV to DVD+VCR on page 11.

AUTO CHANNEL PROGRAMMING

1 Press SYSTEM MENU and the MAIN menu will appear.

2 Press v/V to select the TUNING menu, then

Press b/B repeatedly to switch among TUNER, LINE1 and LINE2.

4 Press v/V to choose the AUTO CHANNEL SET option, then press b/B to set the channel.

The tuner will automatically cycle through all available channels in the area and place them in the tuner’s memory.

•After AUTO CHANNEL SET is complete, the TUN- ING menu will close and return to the TV screen auto- matically.

5 Make sure the TUNING BAND is set appropri- ately (TV or CATV).

•TV : If you are using a standard antenna to receive chan- nels.

CATV : If you are using basic cable to receive channels.

6 Use CHANNEL (+/–) on the remote control or CHANNEL (V/v) on the front panel of the DVD+VCR to cycle through the channels in memory.

TO ADD OR ERASE CHANNELS FROM MEMORY

This feature allows you to add or erase channels from mem- ory manually.

1Press V to choose the CH. ADD/DEL option on the TUNING menu. Press b/B to select a channel to add or erase.

2Press OK to add or erase the channel. Repeat steps 1 and 2 to add or erase channels.

English

3Press MENU to return to the TV screen.