Furuno RP-25 manual Setting up the navigation lines, Nav line menu Video plotter mode

Page 38

2. VIDEO PLOTTER

2.8.4Setting up the navigation lines

Navigation lines can be set up as follows:

1.Press the [NAV MENU], [3] key to show NAV LINE menu.

2.Press the [7] key several times to select VIDEO PLOTTER at NAV LINE DATA (item 7) field.

3.Press the [ENTER] key.

[NAV LINE]

1[VIDEO PLOTTER 1]

2NAV LINE

3

4 NAV WIDTH

OFF/ON 0.00NM

5WPT NO. OFF/ON

6WPT (**)->@->(**)

(**)->(**)

7NAV LINE DATA

VIEO PLOTTER/NAVIGATION

8ARRIVAL ALARM

OFF/ON

0.00 NM

9TURNING LINE OFF/ON REVISED

Nav line menu (Video plotter mode)

4.Press the [4] key several times to select ON at NAV WIDTH (item 4) field.

5.Press the [ENTER] key.

6.Press the numeric key to enter the width for navigation line.

Dashed lines appears at both sides of the navigation line. If unnecessary, select OFF at step 4.

7.Press the [ENTER] key.

8.Press the [5] key several times to select ON at WPT NO. (item 5) field. Waypoint No. and marks appears on the navigation line.

9.Press the [ENTER] key.

10.Press the [6] key and then enter the waypoint number in the following case;

·Enter the number of which you are going to the waypoint

·Skip the waypoint which you are going to, and set the next waypoint as destination

2-24

Image 38
Contents Video Plotter 00080745701 Safety Instructions Word to RP-25 Owners FeaturesForword Iii Your 2805 spec Radar map Video plotterTable of Contents Initial Settings Key panel right side Radar MAPKeys for radar map Preparation Radar map menuEnter mark menu Making a Radar MapSelecting the entering way Enter Mark menu on selecting L/L Shapes for linesLongitude/Latitude OWN Ship Posn Positon Erasing Contents of the Radar Map Cursor data correction Position and bearing correctionRadar map correction Releasing the radar map correctionKeys for video plotter Video PlotterOverview Selecting DisplaysTrue motion automatic return Display modesSample video plotter display Card slot location Chart CardsDisplaying chart cards Adding correcting value to cursor data Chart position correctionCanceling chart correction Video plotter 2 menuHiding/showing graphics Setting up the Video PlotterSetting the navigation data Display select menuNav information 1 menu Nav information 2 menu Nav information 3 menuOwn track plot interval and storage time TrackRecording the own ship’s track Own ship plot, target plot menuOther target plot interval and storage time Recording other ship’s trackSmoothing Erasing track Erase menuSelecting method of entry Marks, LinesEntering mark Selecting mark Entering line Entering independent linesErasing marks/lines on a area Erasing Marks, LinesErasing individual marks/lines Erasing all marks Entering waypoints by the cursor WaypointsEntering waypoints Enter wpt, nav line menuWaypoint list Entering waypoints at own ship’s positionWPT List Enter WPT, NAV Line Wpt list menuWay point menu on selecting video plotter Displaying a waypointInternal storage waypoint External waypoint Way point menu on selecting navigationEntering new navigation line Navigation LinesEntering navigation line Enter nav line menuRemoving waypoints from navigation lines Navigation line listAdding waypoit to navigation lines Deleting all navigation lines Deleting navigation linesDeleting individual navigation lines Setting up the navigation lines Nav line menu Video plotter modePress the Enter key Press the NAV Menu key to close the menu Formatting memory RAM card Recording and Replaying DataDisplaying navigation lines Internal navigation linesRecording data Record card menuReplaying data Replay card menuVideo plotter initial setting menu Maintenance for TechniciansInitial Settings Replacement of Battery on RP Board Do not open the equipmentMenu Tree AP-1AP-2 Latitude Error Table on 96 NM Range AP-3Specifications SP-1