Furuno RP-25 manual Specifications, SP-1

Page 48

SPECIFICATIONS

Radar Plotter

Radar Map

Display

Radar Display, Video Plotter display,

Radar display only

Radar/Video Plotter display

Display Mode

HU*, TM, CU, NU, CG

HU, TM, CU, NU, CG

(No chart available in HU and CG mode)

*Not available in G-type.

Display Range

0.125/0.25/0.5/0.75/1/1.5/2/3/4/6/8/12/16/24/32/48/72/96*/120*

*FR/FAR-2825 only

Projection

Mercator

Ichnography

Useable Range

80ْ latitude or below

Electronic Chart Card

Land features filled

-

Track Capacity

Own ship: 6,000 points

Other ship: 6,000 points

-

Own ship plot interval:

OFF/10sec/30sec/1min/2min/3min/6min

Marks

Mark capacity: 6,000 points

Mark capacity: 1,500 points

Nav Line

Coast line

Contour line

Prohibited line

Cable

Course Line

Internal setting or external input from navaid.

-

Data Display (requires

٠ Own ship’s latitude and longitude position

external sensors)

٠ Cursor latitude and longitude position

٠ Range/bearing, estimated time to arrive to waypoint

-

٠ Range and bearing from origin mark to cursor

٠ Depth

٠ Water temperature

Alarm

Arrival alarm (audible)

SP-1

Image 48

Contents Video Plotter 00080745701 Safety Instructions Features ForwordWord to RP-25 Owners Iii Your 2805 spec Radar map Video plotterTable of Contents Initial Settings Radar MAP Keys for radar mapKey panel right side Preparation Radar map menuMaking a Radar Map Selecting the entering wayEnter mark menu Shapes for lines Longitude/LatitudeEnter Mark menu on selecting L/L OWN Ship Posn Positon Erasing Contents of the Radar Map Position and bearing correction Radar map correctionCursor data correction Releasing the radar map correctionVideo Plotter OverviewKeys for video plotter Selecting DisplaysDisplay modes Sample video plotter displayTrue motion automatic return Chart Cards Displaying chart cardsCard slot location Chart position correction Canceling chart correctionAdding correcting value to cursor data Video plotter 2 menuSetting up the Video Plotter Setting the navigation dataHiding/showing graphics Display select menuNav information 1 menu Nav information 2 menu Nav information 3 menuTrack Recording the own ship’s trackOwn track plot interval and storage time Own ship plot, target plot menuRecording other ship’s track SmoothingOther target plot interval and storage time Erasing track Erase menuMarks, Lines Entering markSelecting method of entry Selecting mark Entering line Entering independent linesErasing Marks, Lines Erasing individual marks/linesErasing marks/lines on a area Erasing all marks Waypoints Entering waypointsEntering waypoints by the cursor Enter wpt, nav line menuWaypoint list Entering waypoints at own ship’s positionWPT List Enter WPT, NAV Line Wpt list menuDisplaying a waypoint Internal storage waypointWay point menu on selecting video plotter External waypoint Way point menu on selecting navigationNavigation Lines Entering navigation lineEntering new navigation line Enter nav line menuNavigation line list Adding waypoit to navigation linesRemoving waypoints from navigation lines Deleting navigation lines Deleting individual navigation linesDeleting all navigation lines Setting up the navigation lines Nav line menu Video plotter modePress the Enter key Press the NAV Menu key to close the menu Recording and Replaying Data Displaying navigation linesFormatting memory RAM card Internal navigation linesRecording data Record card menuReplaying data Replay card menuMaintenance for Technicians Initial SettingsVideo plotter initial setting menu Replacement of Battery on RP Board Do not open the equipmentMenu Tree AP-1AP-2 Latitude Error Table on 96 NM Range AP-3Specifications SP-1