JVC SR-MV50U manual Completed Program Overlap appears on the TV screen, See

					OPERATIONS ON VCR DECK EN 49
Manual Timer Programming					9 Press REC MODE to select the desired recording mode. Or
					press w e to select “SP/EP”, then press rt to select the desired
					recording mode.
You can program this unit to timer record as many as 8 programs.					10 Press ENTER to access the Program Check screen.
If you do not know the PlusCode number for the program you wish
					11 Press PROG/CHECK to complete timer programming.
to record, use the following procedure to set your unit to timer
record the program.					“PROGRAM COMPLETED” appears on the TV screen for about 5
					seconds, then the normal screen appears. If “PROGRAM NOT
● Make sure that the unit’s built-in clock is set properly.					COMPLETED PROGRAM OVERLAP” appears on the TV screen,
● Turn on the unit.					see page 50.
● Turn on the TV and select the video channel (or AV mode).					● To program another timer, repeat steps 3 – 11.
● Slide the TV/CABLE/DBS/DVD switch to DVD.					12 Press VCR TIMER (#) to engage the unit’s timer mode. The
					VCR timer indicator lights up on the front display panel and the
					DVD deck is automatically selected. When the DVD deck is in
VCR TIMER (#)					timer standby mode, the unit is automatically turned off.
					● To disengage the timer mode, press VCR TIMER (#) again.
VCR/DVD
	1	2	3		NOTES:
	4	5	6	0 – 9
	7	8	9		● To Timer Record Weekly Or Daily Serials:
PROG/CHECK		0			— anytime during steps 7 through 9, press number key “9” for
					weekly serials or number key “8” for daily serials (Monday – Friday).
				rtw e	Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the
ENTER					button again makes the corresponding indication disappear.
					● You can program this unit to timer record as many as 8 programs. If
					you try to program the unit to record a ninth, “PROGRAM FULL”
					appears on the TV screen. To record the extra program, you must
					first cancel any unnecessary programs. ( pg. 50)
REC MODE					● In case of a power failure after programming, the unit’s memory
					backup keeps your selections for approximately 5 seconds.

● Programs that start after midnight must have the next day’s date. ● To record the programs received by cable box or DBS receiver,

record on the DVD discs. For details, refer to “Manual Timer Programming” ( pg. 39).

1 Load a cassette with the record safety tab intact. If not, set “REC SAFETY” to “OFF” ( pg. 73).

2 Press VCR/DVD repeatedly so that the VCR lamp lights up on the unit.

3 Press PROG/CHECK to access the Program Check screen.

PR START		STOP	CH	DATE
1	8:00P	10:00	12	12/24
2	10:00A	10:45	40	12/25
3	11:30P	1:00	125	12/25

4

5

6

7

8

(PROG/CHECK) TO NEXT

4 Press rt to select the blank number, then press ENTER. The program screen appears.

5 Press w e to select “START”, then press rt to set the desired start time.

PROGRAM 4
START		STOP
– –:– –AM		– –:– –AM
DATE		CH	SP/EP
– –/– –/– –	– – –			SP

● Each press of rt increases/decreases PRESS (RTYU, 8=DAILY

the start time in 1 minute interval.	9=WEEKLY), THEN (ENTER)
	(PROG/CHECK) TO END

●To increase/decrease the start time in

30-minutes interval, press and hold rt.

6 Press w e to select “STOP”, then press rt to set the desired stop time.

●Each press of rt increases/decreases the stop time in 1 minute interval.

●To increase/decrease the stop time in 30 minutes interval, press and hold rt.

7 Press w e to select “DATE”, then press rt to set the desired date.

●The current date appears on the TV screen. The date you enter appears in its place.

8 Press w e to select “CH”, then press rt to select the desired channel.