JVC SR-MV50U DV Dubbing DVD Deck Only, Performing dubbing without using the DV Dubbing controller

62 EN EDITING

	DV Dubbing (DVD Deck Only)	1 Connect a camcorder or DV equipment to the [DV IN] connector
		on the unit’s front panel.
		2 Load a DVD-RAM/RW/R disc on the unit.
You can dub programs from a camcorder or DV equipment
		3 Press CH +/– to set the channel to “DV DUBBING”.
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or DV		● The “DV DUBBING” controller appears on the TV screen.
equipment functions during dubbing.		● If “	” does not appear on the “DV DUBBING” controller, make

sure the DV equipment is connected correctly.

NOTES:

●Use the DV cable VC-VDV 204U for connection.

●When you connect a PC to the [DV IN] connector, we do not assure the normal operation of this unit.

Your unit

To [DV IN]

4 Press REC MODE repeatedly to set the recording mode.

5 Locate the point from where you want to start dubbing, then stop or pause playback by pressing the following buttons on the remote control: 4, 5, 3, 8, 9

●To play back in slow speed (1/10 of the normal speed), press 9 to pause playback, then press 3 or 5.

●To play back frame-by-frame, press 9 to pause playback, then press 9 repeatedly. Each press of 9 advances a frame.

●To change the playback direction, press 3 or 5.

6 Press w e to select , then press ENTER.

7 Press rt to select the desired

sound track, then press ENTER.

AUDIO 1: Select this to record the original stereo sound played back on the connected DV equipment.

Camcorder

DV equipment

DV cable (VC-VDV 204U)

(not supplied)

DV connector

AUDIO 2: Select this to record the dubbed stereo sound played back on the connected DV equipment.

MIX: Select this to record the sound of both “AUDIO 1” and “AUDIO 2”.

●Note that this selection is not available when the source program is recorded in 16BIT (48 kHz) mode.

8 Press w e to select , then press ENTER. The dubbing starts.

●Playback on the external DV equipment and recording on the unit should start simultaneously.

●When the playback from the beginning is not possible, the “DV DUBBING” controller cannot be used. Perform dubbing without using the “DV DUBBING” controller. ( below)

●To pause dubbing, press w e to select , then press ENTER. Both the unit and the external DV equipment pause dubbing. Pressing 9 on the unit also works the same way.

●To clear the “DV DUBBING” controller from the TV screen, press ON SCREEN.

9 Press 8 on the remote control to stop dubbing.

●Both the unit and the external DV equipment stop dubbing.

NOTES:

●Dubbing copyright guarded programs is not possible.

●Original DV information such as the recording date and time are not recorded.

●The superimposed indication during the operation or dubbing is not recorded.

●It is not possible to perform dubbing when “VCR]” lights up on the unit. Press VCR] so that “VCR]” lights off.

Performing dubbing without using the “DV DUBBING” controller

APress CH +/– to set the channel to “DV DUBBING”.

BPress REC MODE repeatedly to set the recording mode.

CStart playback on the external DV equipment slightly before the actual point from where you wish to start dubbing.

D Press 7 on the unit to start recording. Or while holding 7, press 4 on the remote control. The dubbing starts.

E When the dubbing ends, press 8 on the unit, then stop playback on the external DV equipment.