Cloning Procedures (Cont.)
Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer
Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs, as this will damage the clone programmer and the PPV card.
Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure).
LT2002 Cloning Notes
• Read the IMPORTANT CLONING |
INFORMATION on page 23 before |
beginning any cloning procedures. |
• A slow flashing green light indicates |
that there are communication |
| MPI |
Antenna | Cable |
| |
or CATV |
|
| problems between the TV and the |
| LT2002 clone programmer. If this is |
| the case, check for a damaged |
| cable, poor contacts, or other |
| connection troubles. |
• | If the status indicator is red, the |
| LT2002 batteries are low and |
| should be replaced. Install four (4) |
| |
• | Learning and Teaching is only |
| possible between identical model |
| TVs; however, the LT2002 clone |
| programmer can store up to three |
| different Master TV Setups. |
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION XX
THE SW IS REViSION XX
CLONE CLOCK = XX:XX
TV | CLOCK = XX:XX |
- PRESS ANY KEY TO CONTINUE
Ferrite Core (TDK, ZCAT
LT2002 Clone Programmer
Connect cable to |
|
|
|
|
|
| |
TV MPI Jack and |
| Status | |||||
follow on screen |
| ||||||
instructions |
| Indicator | |||||
| MPI |
|
|
|
| ||
|
|
|
|
|
|
| Reset |
|
|
|
| Color | |||
| • green |
| battery ok | ||||
| • red |
| battery low | ||||
|
|
| Blink pattern |
| |||
| • slow |
| power on | ||||
no communications
•heartbeat power on communications ok
®
QuickSet II Programmer
LT2002
ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA
Learn Setup from Master TV
1.Ensure the Master TV is set up completely and in
2.If an analog channel is not available, direct tune the TV to an Aux source, or select an Aux source, such as
3.If there is a good connection after the LT2002 is connected to the TV MPI port, “THE CLONE HAS CONTROL OF THE TV” message will appear on the TV screen. Press any key on the Installer Remote to access the LT2002 Clone Selection Menu.
4.Press 1 on the Installer Remote to select LEARN FROM TV from the Clone Selection Menu; then press ENTER to proceed to the Memory Bank Selec- tion Menu (see sample screen on next page).
5.Press 1, 2, or 3 on the Installer Remote to select the clone Memory Bank in which to store the Master Setup. Then, press ENTER.
Note: If you choose a Memory Bank that already has a Master device’s setup programmed into it, that setup will be overwritten by the new Master TV Setup.
(Continued on next page)
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION | XX | |
THE SW IS REVISION | XX | |
CLONE CLOCK = XX:XX |
| |
TV | CLOCK = XX:XX |
|
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
CLONE SELECTION MENU
(1) LEARN FROM TV
(2)TEACH TO TV
(3)SET CLONE CLOCK FROM TV
(4)SET TV CLOCK FROM CLONE
(5)DISPLAY TV SETUP
(6)DISPLAY CLONE SETUP
-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.
-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.
27 |