Firstech, LLC CM3 SERIES, CM1000A, CM4200 manual Connector

Page 21

Pin 8 Black- Ground (-) negative input. This wire will connect to chassis ground.

CONNECTOR 2

These outputs can be used to trigger the secondary external pre-wired relay on the main ignition harness. (I.e.: 2nd ignition (-) negative output green wire connected to the violet wire of the relay will give you a 2nd ignition (+) positive output on the blue wire of the relay.

Pin 1 Green/White- Parking light 250mA (-) negative output. This is an optional output that will provide a (-) negative output with parking light flash.

Pin 2 Black- Status 250mA (-) negative output. This is an optional output that will provide a (-) negative output before the ignition is triggered, during remote start and will shut down after ignition has shut down. (Note: This wire can be used to trigger factory security interface modules)

Pin 3 Green- 2nd Ignition 250mA (-) negative output. This is an optional output that will provide a (-) negative output while the ignition is triggered and during remote start.

Pin 4 White/Black- 2nd Accessory 250mA (-) negative output. This is an optional output that will provide a (-) negative output while the accessory output is triggered.

Pin5 Red/Black- 2nd Starter 250mA (-) negative output. This is an optional output that will provide a (-) negative output during crank only.

CONNECTOR 3

Pin 1 Light Blue- Parking brake (-) negative input. This input is required for manual transmission reservation mode and to trigger the turbo-timer mode. The proper wire will provide a (-) negative trigger only when parking brake is set. (Note: Turbo mode is optional.)

Pin 2 Gray/Black- Hood-pin (-) negative input. This input is a safety shut down that will prevent the vehicle from remote starting and shut down the engine when the hood is opened. (Note: This wire will also trigger the alarm when the system is armed.)

Pin 3 Light Blue/White- Brake 12-volts (+) positive input. This input is required to shut down vehicle when remote started. The proper wire will test 12-volts (+) positive only when the foot brake is pressed.

- 21 -

Image 21
Contents Master Install Guide CM3 Series CM4200 CM1000A Page Table of Contents Install Checklist Remote Programming Procedures Page Remote Programming Procedures 2WFMR-S,2WAMR, 2WFMR, and 2W900FMR 1WFM6RPage Page Common Procedures Page Antenna Mounting Dipswitch and Jumper SettingsAdjusting Shock Sensor Sensitivity Adjusting Siren VolumeLittle Green Loop Programming Tach / Alternator Sensing Tach sensingAlternator sensing Diagnosing Remote Start ProblemsPage Control Modules Page CN1 CN2 CN3 CN4 CN5 CN6 CN7 CM3000 Wiring DiagramCM-3000 Wiring Detail Connector Pin 1 Not used Pin 8 Not used Pin 6 Not usedPre-wired Shock Sensor Pre-wired Antenna Cable Page CN1 CM3300 Wiring DiagramCM-3300 Wiring Detail Connector Pre-wired L.E.D Pre-wired Remote Paging Sensor or R.P.S Page JM1 CM4200 Wiring DiagramCM-4200 Wiring Detail Connector Pin 1 Not used Optional Temperature sensor Page CM1000A Wiring Diagram CM-1000A Wiring Detail Connector Pre-wired L.E.D Option Programming Page Option Programming 1WAM4R, 1WFM4R, 1W900FM4R, and 1WSS4R R500A CM1000A 2WFMR-S, 2WAMR, 2WFMR, and 2W900FMR 1WFM6RCM3 Series Option Programmer 2WSSRWay 4 Button Remotes All 2-Way Remotes CM3000 Option Menu Feature CM3300 Option Menu Feature CM4200 Option Menu Sec Anti-Jacking Ign Kill Enabled Options Explained In Detail CM3000-3300-4200 CM3000 CM4200 Page Additional Programming Page Installation Assistance Page Frequently Asked Questions / Troubleshooting Do I have to hook up both 12v+ wires? Vehicle will remote start when disarmed, but not when armedHow do I upgrade my current install to a higher end model? Vehicle starts then shuts down 3 times in a rowCommon Diagrams Adding Door Actuators Trunk Release Transponder Passlock Passlock Aftermarket Turbo Timer with Parking Brake Trigger Starter Kill Relay Installation Page Page Page Accessory Manuals Page OP500 Option Programmer Stand Alone ModeConnector 1 Input Connector 2 OutputChannel Expander Temperature Sensor RPS Remote Paging SensorProgramming the Outputs