Firstech, LLC CM3 SERIES, CM1000A, CM4200 manual 2WSSR, CM3 Series Option Programmer

Page 48

3.Wait a few seconds, and the parking lights will flash the number of times corresponding to the option number you are about to modify. If the number of times the lights flash does not correspond with the option you want to change, wait a few seconds and the siren/horn will sound, signaling that you have exited programming mode. After the siren/horn sounds, you can retry the process from the beginning.

4.Immediately after the parking lights stop flashing from step 3, press:

a.Button ( I ) for the factory default setting. The parking lights will flash once.

b.Button ( II ) for the optional setting. The parking lights will flash twice.

You will need to perform these steps for each option you would like to change.

2WSSR

The 2WSSR programs options just like the other 2-way remotes listed above, but a more focused approach may be needed. Inherent to the type of technology used in the 2WSSR, is a noticeably longer delay in the response time. Given the delayed response time, and that the option programming is a timed process in itself, option programming with this remote can be a more difficult process if you are not sure of which buttons you need to press during the process. Another option is the below mentioned Option Programmer, which eliminates the need for remote option programming altogether.

CM3 Series Option Programmer

The Option Programmer is an installer’s tool used to modify options within the CompuStar System. This unit plugs into the CompuStar system through the antenna cable and is powered through this cable as well, therefore requiring no batteries to replace. The Option Programmer makes it easier to program options available to remote programming and also makes available some options that the remotes are unable to modify. The Option Programmer has its own user’s guide in the “Accessory Manuals” section.

Resetting all of Menu #1 or Menu #2

to the factory default settings.

If you are not sure about current programming, you can change everything to the factory settings and start again.

- 48 -

Image 48
Contents Master Install Guide CM3 Series CM4200 CM1000A Page Table of Contents Install Checklist Remote Programming Procedures Page Remote Programming Procedures 1WFM6R 2WFMR-S,2WAMR, 2WFMR, and 2W900FMRPage Page Common Procedures Page Dipswitch and Jumper Settings Antenna MountingAdjusting Siren Volume Adjusting Shock Sensor SensitivityLittle Green Loop Programming Tach / Alternator Sensing Tach sensingDiagnosing Remote Start Problems Alternator sensingPage Control Modules Page CM3000 Wiring Diagram CN1 CN2 CN3 CN4 CN5 CN6 CN7CM-3000 Wiring Detail Connector Pin 1 Not used Pin 6 Not used Pin 8 Not usedPre-wired Shock Sensor Pre-wired Antenna Cable Page CM3300 Wiring Diagram CN1CM-3300 Wiring Detail Connector Pre-wired L.E.D Pre-wired Remote Paging Sensor or R.P.S Page CM4200 Wiring Diagram JM1CM-4200 Wiring Detail Connector Pin 1 Not used Optional Temperature sensor Page CM1000A Wiring Diagram CM-1000A Wiring Detail Connector Pre-wired L.E.D Option Programming Page Option Programming 1WAM4R, 1WFM4R, 1W900FM4R, and 1WSS4R R500A CM1000A 1WFM6R 2WFMR-S, 2WAMR, 2WFMR, and 2W900FMR2WSSR CM3 Series Option ProgrammerWay 4 Button Remotes All 2-Way Remotes CM3000 Option Menu Feature CM3300 Option Menu Feature CM4200 Option Menu Sec Anti-Jacking Ign Kill Enabled Options Explained In Detail CM3000-3300-4200 CM3000 CM4200 Page Additional Programming Page Installation Assistance Page Frequently Asked Questions / Troubleshooting Vehicle will remote start when disarmed, but not when armed Do I have to hook up both 12v+ wires?How do I upgrade my current install to a higher end model? Vehicle starts then shuts down 3 times in a rowCommon Diagrams Adding Door Actuators Trunk Release Transponder Passlock Passlock Aftermarket Turbo Timer with Parking Brake Trigger Starter Kill Relay Installation Page Page Page Accessory Manuals Page Stand Alone Mode OP500 Option ProgrammerConnector 1 Input Connector 2 OutputChannel Expander Temperature Sensor RPS Remote Paging SensorProgramming the Outputs