Firstech, LLC CM1000A, CM3 SERIES, CM4200 manual Optional Temperature sensor

Page 37

Pin 5 Blue/Black- Lock 250mA (-) negative output. This wire will provide a (-) negative pulse output during lock. (Note: Positive and reverse polarity will require additional relays.

Pin 6 Not used.

CONNECTOR 5

(Optional Temperature sensor)

Pin 1 Gray-12-volt (+) positive output. This wire will provide 12-volt (+) positive to temperature sensor.

Pin 2 Brown-Temp sensor (-) negative input. This wire will activate remote start when provided a (-) negative input. (Note: If vehicle is remotely started, a (-) negative input will turn the vehicle off.)

Pin 3 Black-Temp sensor (-) negative ground output.

CONNECTOR 6

(Pre-wired Antenna Cable)

Pin 1 Yellow-RX input. This wire receives signal from remote.

Pin 2 White-TX output. This wire transmits signal to remote.

Pin 3 Red-12-volt constant (+) positive input.

Pin 4 Black- (-) negative ground input.

CONNECTOR 7

RS 232

Pin 1 Yellow-RX input. This wire receives signal from remote.

Pin 2 Blue-TX output. This wire transmits signal to remote.

Pin 3 Black-(-) negative ground in

Pin 4 Red-12-volt constant (+) positive input.

- 37 -

Image 37
Contents Master Install Guide CM3 Series CM4200 CM1000A Page Table of Contents Install Checklist Remote Programming Procedures Page Remote Programming Procedures 2WFMR-S,2WAMR, 2WFMR, and 2W900FMR 1WFM6RPage Page Common Procedures Page Antenna Mounting Dipswitch and Jumper SettingsAdjusting Shock Sensor Sensitivity Adjusting Siren VolumeLittle Green Loop Programming Tach / Alternator Sensing Tach sensingAlternator sensing Diagnosing Remote Start ProblemsPage Control Modules Page CN1 CN2 CN3 CN4 CN5 CN6 CN7 CM3000 Wiring DiagramCM-3000 Wiring Detail Connector Pin 1 Not used Pin 8 Not used Pin 6 Not usedPre-wired Shock Sensor Pre-wired Antenna Cable Page CN1 CM3300 Wiring DiagramCM-3300 Wiring Detail Connector Pre-wired L.E.D Pre-wired Remote Paging Sensor or R.P.S Page JM1 CM4200 Wiring DiagramCM-4200 Wiring Detail Connector Pin 1 Not used Optional Temperature sensor Page CM1000A Wiring Diagram CM-1000A Wiring Detail Connector Pre-wired L.E.D Option Programming Page Option Programming 1WAM4R, 1WFM4R, 1W900FM4R, and 1WSS4R R500A CM1000A 2WFMR-S, 2WAMR, 2WFMR, and 2W900FMR 1WFM6RCM3 Series Option Programmer 2WSSRWay 4 Button Remotes All 2-Way Remotes CM3000 Option Menu Feature CM3300 Option Menu Feature CM4200 Option Menu Sec Anti-Jacking Ign Kill Enabled Options Explained In Detail CM3000-3300-4200 CM3000 CM4200 Page Additional Programming Page Installation Assistance Page Frequently Asked Questions / Troubleshooting Do I have to hook up both 12v+ wires? Vehicle will remote start when disarmed, but not when armedHow do I upgrade my current install to a higher end model? Vehicle starts then shuts down 3 times in a rowCommon Diagrams Adding Door Actuators Trunk Release Transponder Passlock Passlock Aftermarket Turbo Timer with Parking Brake Trigger Starter Kill Relay Installation Page Page Page Accessory Manuals Page OP500 Option Programmer Stand Alone ModeConnector 2 Output Connector 1 InputChannel Expander RPS Remote Paging Sensor Temperature SensorProgramming the Outputs