Firstech, LLC CM4200, CM3 SERIES, CM1000A manual Connector

Page 35

CONNECTOR 2

Pin 1 Green/White- Parking light 250mA (-) negative output. This is an optional output that will provide a (-) negative output with parking light flash.

Pin 2 Red/Black- 2nd Starter 250mA (-) negative output. This is an optional output that will provide a (-) negative output during crank only.

Pin 3 Violet- 250mA (-) negative output when locked and remote started. This wire will provide a (-) negative output when system is locked and armed and during remote start for anti-grind. (Note: This wire can also be used to trigger after-market L.E.D. kits and other after-market accessories. Output must be diode isolated when used to trigger after-market accessories.)

Pin 4 Black- Status 250mA (-) negative output. This is an optional output that will provide a (-) negative output before the ignition is triggered, during remote start and will shut down after ignition has shut down. (Note: This wire can be used to trigger factory security interface modules)

Pin 5 Orange- Factory alarm re-arm 250mA (-) negative output. This is an optional output that will provide a (-) negative pulse output during lock, after crank and after ignition shut down.

Pin 6 Orange/White- Factory alarm disarm 250mA (-) negative output. This is an optional output that will provide a (-) negative pulse output during unlock and before ignition is turned on.

Pin 7 White- Horn honk 250mA (-) negative output. This is an optional output that will provide a (-) negative pulse when the door locks are activated and 30 or 60 second pulse output during panic.

CONNECTOR 3

Pin 1 Light Blue- Parking brake (-) negative input. This input is required for manual transmission reservation mode and to trigger the turbo-timer mode. The proper wire will provide a (-) negative trigger only when parking brake is set. (Note: Turbo mode is optional.)

Pin 2 Gray/Black- Hood-pin (-) negative input. This input is a safety shut down that will prevent the vehicle from remote starting and shut down the engine when the hood is opened. (Note: This wire will also trigger the alarm when the system is armed.)

- 35 -

Image 35
Contents Master Install Guide CM3 Series CM4200 CM1000A Page Table of Contents Install Checklist Remote Programming Procedures Page Remote Programming Procedures 2WFMR-S,2WAMR, 2WFMR, and 2W900FMR 1WFM6RPage Page Common Procedures Page Antenna Mounting Dipswitch and Jumper SettingsProgramming Tach / Alternator Sensing Tach sensing Adjusting Siren VolumeAdjusting Shock Sensor Sensitivity Little Green LoopAlternator sensing Diagnosing Remote Start ProblemsPage Control Modules Page CN1 CN2 CN3 CN4 CN5 CN6 CN7 CM3000 Wiring DiagramCM-3000 Wiring Detail Connector Pin 1 Not used Pin 8 Not used Pin 6 Not usedPre-wired Shock Sensor Pre-wired Antenna Cable Page CN1 CM3300 Wiring DiagramCM-3300 Wiring Detail Connector Pre-wired L.E.D Pre-wired Remote Paging Sensor or R.P.S Page JM1 CM4200 Wiring DiagramCM-4200 Wiring Detail Connector Pin 1 Not used Optional Temperature sensor Page CM1000A Wiring Diagram CM-1000A Wiring Detail Connector Pre-wired L.E.D Option Programming Page Option Programming 1WAM4R, 1WFM4R, 1W900FM4R, and 1WSS4R R500A CM1000A 2WFMR-S, 2WAMR, 2WFMR, and 2W900FMR 1WFM6RCM3 Series Option Programmer 2WSSRWay 4 Button Remotes All 2-Way Remotes CM3000 Option Menu Feature CM3300 Option Menu Feature CM4200 Option Menu Sec Anti-Jacking Ign Kill Enabled Options Explained In Detail CM3000-3300-4200 CM3000 CM4200 Page Additional Programming Page Installation Assistance Page Frequently Asked Questions / Troubleshooting Vehicle starts then shuts down 3 times in a row Vehicle will remote start when disarmed, but not when armedDo I have to hook up both 12v+ wires? How do I upgrade my current install to a higher end model?Common Diagrams Adding Door Actuators Trunk Release Transponder Passlock Passlock Aftermarket Turbo Timer with Parking Brake Trigger Starter Kill Relay Installation Page Page Page Accessory Manuals Page OP500 Option Programmer Stand Alone ModeChannel Expander Connector 1 InputConnector 2 Output Programming the Outputs Temperature SensorRPS Remote Paging Sensor