Wegener Communications 562 manual Search Functions, Perms/Temps/Searching & Settings

Page 51

Unity 552 User’s Manual

CHAPTER 4 SEARCH FUNCTIONS

4.1 Perms/Temps/Searching & Settings

The term "settings" is used throughout this document and includes the following set of parameters:

 

Table 4.1: Settings Parameters for the iPump 562

 

 

 

Setting

 

Description

 

 

 

Modulation

 

S28PSK/S2QPSK/QPSK

 

 

 

RF Switch/Pol

 

If IRD is configured for Universal LNB, H or V are valid. Specify RF port 1-

 

 

4 for four-port RF configuration.

 

 

 

Carrier

 

The downlink frequency specified in MHz with up to two decimal places.

 

 

This value’s absolute difference with the LNB LO frequency is used as

 

 

specified in the technical specifications. (e.g. 3720.00 MHz).

 

 

 

Data_rate

 

Data rate is specified in Mbps with up to three decimal places. See the

 

 

technical specifications for the applicable range. (e.g. 41.470 Mbps).

 

 

 

Fec_rate

 

The inner FEC code ratio and can have one of the values specified in the

 

 

technical specifications. (e.g. 3/4).

 

 

 

Tag_site

 

Value of 0-14 (15 is a special NO Tag case) specifying the location of this

 

 

carrier’s tag frequency.

 

 

 

[program]

 

The program number from the MPEG Program Association Table. This

 

 

must be number from 1 to 65535. If omitted or an ‘*’ is entered, the unit

 

 

will select the first available program stream. Note that this number points

 

 

to the PID for the Program Map Table for what we might call a “service” (a

 

 

single video channel and associated audio signals).

 

 

 

Label

 

A string of characters for identification.

 

 

 

The IRD is acting on one of three groups of settings at any given time, each of which is described in Table 4.2

www.wegener.com

800092-01 Rev. A

41

Image 51
Contents IPump 800092-01 Rev. a First Edition July Wegener Communications, IncFCC Part 15B Class A, UL/C-UL1950 3rd EN5502498 Table of Contents Controlling and Monitoring Erminal D Iagterm C Ommands This page intentionally left blank 800092-01 Rev. a List of Tables This page intentionally left blank 800092-01 Rev. a List of Figures 34 iPump 562 OSD Display Current Warnings Digital Media Sever General InformationManual Overview Product OverviewRear Panel IPump 562 Product SpecificationsFeatures and Options Compel Network Con- trolInterfaces ConnectionsExternal Input/OutputExternal Input/Output Interfaces Pdif Digital Audio Connector Input/Output DescriptionHdmi Digital Audio/Video Connector Input/Output Description Connector Input/Output DescriptionRF Characteristics IPump 562 RF CharacteristicsTechnical Specifica- tions IPump 562 Video Decoder Video DecoderComposite Video Output IPump 562 Composite Video OutputComponent Video Output IPump 562 Unbalanced Audio Output IPump 562 Component Video OutputAudio Decoder Unbalanced Audio OutputLocal Hard Disk Driver HDD LNB DC Power RF Port 1 onlyAC Power Serial PortPhysical Characteristics Safety SummaryPhysical Characteristics 14 iPump 562 Physical CharacteristicsLocation and Mounting InstallationPrecautions Unpacking and InspectionRack Mounting Desktop InstallationCircuit Overloading Reliable EarthingFront Panel Controls Indicators OperationControlling and Monitoring Push-buttons Menu Navigation using Push-buttonsNormal Diagterm Terminal CommandsMode LED Status Condition AlarmControl Normal FunctionsCompel SystemCarrier Settings screen Tune to a carrierCurrent Channel screen Configure LNB options LNB Setup screenChannel Information Options Monitor Signal Quality LNB configuration optionsSignal Quality Setup screen Indicator Threshold screen IPump 562 OSD Signal Quality Setup ScreenIndicator Threshold screen options Signal Strength Meter screenSubtitling Setup screen Operation Subtitling Setup screen optionsConfigure the Advanced Setup screen Unit forUnit Setup screen 11 iPump 562 OSD Advanced SetupVideo Decoder Options Set Decoder OptionsAudio Output Options Setup AudioSet LAN IP Networking options Select Activate SettingsSet LAN-based Decode options LAN Decode OptionsSet Terminal options 10 Networking Configuration Settings11 Terminal Options Set Printer OptionsOption Possible values Console Baud-rate Option Possible values User Relay On/Off 12 User Relay Setup OptionsSet User Relay Set Date and Time informationYes / No 13 Date and Time Information SettingsSwitch Application to different software version Set Unit LabelUnit Status screen Monitor Status InformationCurrent Quality screen Signal Quality screenSignal Quality screen History This Setting screenQuery Network History Elapsed Times screenFind Software Version information Display LAN IP Network informationClear Statistics used for diagnosis 29 iPump 562 OSD Version InfoPlay out play lists of media files View Alarms/Warnings32 iPump 562 OSD Main Menu 34 iPump 562 OSD Display Current Warnings This page intentionally left blank 800092-01 Rev. a Perms/Temps/Searching & Settings Settings Parameters for the iPumpSearch Functions Settings Table or Search Table Signal Quality MonitoringIPump 562 Settings Groups Parameter Description Modulation Signal Quality InformationFrequency Tagging General RulesThis page intentionally left blank 800092-01 Rev. a Customer Service WarrantyTechnical Support Customer Service Appendix 1 Terminal Diagterm Commands Apx 1.1 Diagterm Group CommandsTable Apx 1.1 Diagterm Group Commands Apx 1.2 Diagterm Individual Commands Table Apx 1.2 Diagterm Individual Commands 800092-01 Rev. a Appendix 2 Menu Tree Main Apx 3.1 Return Materials Authorization Request Form Mail service@wegener.com Fax 678Appendix 3 RMA Request Form This page intentionally left blank 800092-01 Rev. a Numerics IndexPdif , 4 search