Wegener Communications 562 manual Circuit Overloading, Reliable Earthing, Rack Mounting

Page 22

Installation

loading must be considered. Also, do not rest any unsupported equipment on a rack- mounted iPump 562 unit.

Circuit Overloading

Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits could have on overcurrent protection and supply wiring. Ensure that the total rack or breaker power consumption does not exceed the limits of the AC branch circuit. Appropriate consideration of equipment ratings should be used when addressing this concern.

Reliable Earthing

When connecting the iPump 562 unit to the power supply, review the ratings of all equipment in the circuit to ensure that the branch circuit, as well as the power source, will not be overloaded. Also make sure that the unit is properly grounded and/or that a protected power strip is used to attach it to the power supply

Rack Mounting

The iPump 562 unit should be installed in such a way that a half-inch clearance is allowed on each side and a quarter-inch on the top to ensure adequate air flow. Ensure that a hazardous condition is not produced by uneven loading, or by resting any unsupported equipment on a rack-mounted iPump 562 unit.

Parts for the iPump 562 unit include 2 angle rack mount brackets and 4 rubber feet. For rack mounting, do not attach the rubber feet as they interfere with the rack mounting.

1.Remove the 2 screws from the left and right sides of the unit.

2.Insert the angle brackets into the left and right sides of the unit ensuring that the screw holes for the unit and brackets are aligned.

3.Secure the brackets by re-inserting the screws through the brackets and unit.

4.Install the unit onto the rack.

Note: The front brackets must be secured to the rack. If the front brackets are left unsecured, the unit may shift forward and fall from the rack, and may result in personal injury and/or damage to the equipment. The internal temperature of the

rack should not exceed 40o C.

Desktop Installation

Parts for the iPump 562 unit include 2 angle rack mount brackets and 4 rubber feet. For desktop installation, do not attach the brackets.

1.Attach the 4 rubber feet onto the indented areas at the bottom of the unit.

2.Place the unit on a flat surface where it will not be subject to spills or impacts.

3.Route cables to the unit so that they will not be hit or pulled, causing damage to the connectors or to the unit itself. Ensure a sufficient flow of cool air so that the unit's operating ambient temperature range is not exceeded.

12

800092-01 Rev. A

www.wegener.com

Page 21 Page 23
Image 22
Page 21 Page 23
Contents IPump Wegener Communications, Inc 800092-01 Rev. a First Edition JulyFCC Part 15B Class A, UL/C-UL1950 3rd EN5502498 Table of Contents Controlling and Monitoring Erminal D Iagterm C Ommands This page intentionally left blank 800092-01 Rev. a List of Tables This page intentionally left blank 800092-01 Rev. a List of Figures 34 iPump 562 OSD Display Current Warnings Product Overview General InformationManual Overview Digital Media SeverCompel Network Con- trol IPump 562 Product SpecificationsFeatures and Options Rear PanelInput/Output ConnectionsExternal InterfacesConnector Input/Output Description Pdif Digital Audio Connector Input/Output DescriptionHdmi Digital Audio/Video Connector Input/Output Description External Input/Output InterfacesIPump 562 RF Characteristics RF CharacteristicsTechnical Specifica- tions Video Decoder IPump 562 Video DecoderIPump 562 Composite Video Output Composite Video OutputComponent Video Output Unbalanced Audio Output IPump 562 Component Video OutputAudio Decoder IPump 562 Unbalanced Audio OutputSerial Port LNB DC Power RF Port 1 onlyAC Power Local Hard Disk Driver HDD14 iPump 562 Physical Characteristics Safety SummaryPhysical Characteristics Physical CharacteristicsUnpacking and Inspection InstallationPrecautions Location and MountingReliable Earthing Desktop InstallationCircuit Overloading Rack MountingOperation Front Panel Controls IndicatorsControlling and Monitoring Menu Navigation using Push-buttons Push-buttonsAlarm Diagterm Terminal CommandsMode LED Status Condition NormalSystem Normal FunctionsCompel ControlTune to a carrier Carrier Settings screenCurrent Channel screen LNB Setup screen Configure LNB optionsChannel Information Options LNB configuration options Monitor Signal QualitySignal Quality Setup screen IPump 562 OSD Signal Quality Setup Screen Indicator Threshold screenSignal Strength Meter screen Indicator Threshold screen optionsSubtitling Setup screen Unit for Subtitling Setup screen optionsConfigure the Advanced Setup screen Operation11 iPump 562 OSD Advanced Setup Unit Setup screenSet Decoder Options Video Decoder OptionsSetup Audio Audio Output OptionsLAN Decode Options Select Activate SettingsSet LAN-based Decode options Set LAN IP Networking options10 Networking Configuration Settings Set Terminal optionsSet Printer Options 11 Terminal OptionsOption Possible values Console Baud-rate Set Date and Time information 12 User Relay Setup OptionsSet User Relay Option Possible values User Relay On/OffSet Unit Label 13 Date and Time Information SettingsSwitch Application to different software version Yes / NoMonitor Status Information Unit Status screenSignal Quality screen Current Quality screenHistory This Setting screen Signal Quality screenElapsed Times screen Query Network HistoryDisplay LAN IP Network information Find Software Version information29 iPump 562 OSD Version Info Clear Statistics used for diagnosisView Alarms/Warnings Play out play lists of media files32 iPump 562 OSD Main Menu 34 iPump 562 OSD Display Current Warnings This page intentionally left blank 800092-01 Rev. a Settings Parameters for the iPump Perms/Temps/Searching & SettingsSearch Functions Signal Quality Monitoring Settings Table or Search TableIPump 562 Settings Groups General Rules Signal Quality InformationFrequency Tagging Parameter Description ModulationThis page intentionally left blank 800092-01 Rev. a Warranty Customer ServiceTechnical Support Customer Service Apx 1.1 Diagterm Group Commands Appendix 1 Terminal Diagterm CommandsTable Apx 1.1 Diagterm Group Commands Apx 1.2 Diagterm Individual Commands Table Apx 1.2 Diagterm Individual Commands 800092-01 Rev. a Appendix 2 Menu Tree Main Mail service@wegener.com Fax 678 Apx 3.1 Return Materials Authorization Request FormAppendix 3 RMA Request Form This page intentionally left blank 800092-01 Rev. a Index NumericsPdif , 4 search
Top Page Image Contents