Technicolor - Thomson RCR311B manual To program the remote to control a VCR or DVD

Page 5

Brand Code Search key (TV, VCR•DVD, SAT•CBL, ON•OFF, GO BACK, and number keys 0-9), the search times out after two minutes. When the search times out, the illuminated ON•OFF key blinks four times and turns off. The last programmed code under that component key is retained.

3.If you are programming the remote to control your TV, satellite receiver or cable box, go directly to step 5.

4.To program the remote to control a VCR or DVD. The

VCR•DVD key can control only one component, either your VCR or your DVD. To program your remote to control either your DVD or your VCR, you must first put the remote in the proper programming mode. Follow these directions before proceeding to step 5.

VCR•DVD ON•OFF

VCR•DVD

VCR•DVD ON•OFF

(BLINK)

VCR•DVD

a.Press and hold the VCR•DVD key. The illuminated ON•OFF key turns on.

b.While holding down the VCR•DVD key, press and release the number 2 key on the keypad to control a VCR or the number 3 key to control a DVD. The illuminated ON•OFF key blinks, and then turns back on.

c.Release the VCR•DVD key. The illuminated ON•OFF key blinks four times and then turns off.

Your remote is now either in VCR or DVD Programming Mode, depending on which you chose. Proceed to step 5.

TV SAT•CBL

ON•OFF

(BLINK)

ON•OFF

ON•OFF

(BLINK)

5.Press and hold the component key (TV, VCR•DVD, SAT•CBL) you wish to program. The illuminated ON•OFF key turns on and remains on.

6.While holding the component key down, press and hold the ON•OFF key. The illuminated ON•OFF key turns off.

7.After holding both keys down for three seconds, the illuminated ON•OFF key turns back on.

8.Release both keys. The illuminated ON•OFF key remains on.

9.Refer to the Brand Codes in the enclosed Code Lists. Press and release the appropriate brand code key (Numbers 0-9), using the number keys on the keypad. The illuminated ON•OFF key blinks once.

ON•OFF

ON•OFF

(BLINK)

Throughout the programming of each key, be sure to keep the remote pointed at the IR sensor of the component you are currently programming the remote to control.

10.Press and release the ON•OFF key repeatedly until your component turns off. Each time you press the ON•OFF key, the illuminated ON•OFF key blinks, and the next code is sent. The Brand Code Search begins with the first code in the chosen brand list for that component and cycles through all the codes for that brand. If your component turns off, you have found the correct code. (If it cycles through and the illuminated ON•OFF key blinks four times and turns off, all codes in the chosen

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents
I V E R S a L Table of Contents Backlighting Battery Installation and InformationBattery Saver Programming Methods Illuminated Onoff KeyProgramming the Remote To program the remote to control a VCR or DVD. Direct Code Entry Manual Code Search and Entry Auto Code Search and Entry Press and release the Play key Code Retrieval On-screen Menus Using the Remote to Control Your ComponentsAre in the Menu Mode Sleep Timer Select Models OnlyProblem The remote is not performing commands properly TroubleshootingProblem The remote does not operate your component Problem The VCR won’t record Limited 90-Day WarrantyTélécommande Satcbl Table des matièresRétroéclairage Installation des piles et informationÉconomiseur de piles Touche Onoff éclairée Programmation de la télécommandeMéthodes de programmation Recherche et entrée de code de marqueRelâchez la touche VCRDVD. La Entrée directe de code Méthodes de programmation suiteRecherche et entrée de code manuelles Maintenez la touche Vcrdvd Recherche et entrée de code automatique Maintenez la touche Vcrdvd enfoncée et appuyez sur la touche ONOFF. La touche Onoff Récupération de codeRécupération de code suite Utilisation de la télécommande avec vos appareilsMinuterie-sommeil Certains modèles seulement Menus à l’écranDépannage Problème La télécommande ne commande pas votre appareilMinuterie-sommeil certains modèles seulement suite Page Problème Le magnétoscope n’enregistre pas Dépannage suiteGarantie limitée de 90 jours Control remoto TV, VCRDVD, Satcbl ÍndiceIluminación del teclado Instalación de las pilas e informaciónInterruptor economizador de pilas Cómo programar el control remoto Tecla Onoff iluminadaMétodos de programación Búsqueda y registro de códigos de marcasVcrdvd Onoff Parpadee Registro directo de códigos Métodos de programación continúaMétodo manual de búsqueda y registro de códigos Después de mantener las dos teclas Debe oprimir la tecla Stop Método automático de búsqueda y registro de códigosOnoff Play Parpadee Reverse Onoff Forward Stop Recuperación de códigos Menús en pantalla Recuperación de códigos continúaApagado programado en algunos modelos solamente Cómo salir del menúApagado programado en algunos modelos solamente continúa Detección y solución de problemasProblema el control remoto no hace funcionar el aparato Problema el VCR no graba Garantía limitada de 90 días Detección y solución De problemas continúaPage Compatible with today’s most popular brands
Top Page Image Contents