TOA Electronics C-RM500 operating instructions S P E E D, M E R a, 4 0, M O T E, 2 0

Page 29

6.4.6. I/O speed

Sets each control terminal's transfer rate.

Step 1. Press the Menu key to display the menu screen.

Step 2. Tilt the joystick up or down to select "I/O SPEED" then press the SET key to confirm the selection.

The screen for selecting the control terminal is displayed.

Step 3. Tilt the joystick left or right to select the control terminal. Select the control terminal from "CAMERA," "SWCHER" (switcher), "REMOTE" (Remote Control Unit), and "ALARM."

I / O S P E E D

2

I / O S P E E D

SET

C A M E R A

Step 4. Press the SET key to confirm the selected control terminal. The transfer rate is shown on Line 2. In this event, the current setting is displayed.

Step 5. Tilt the joystick left or right to select the transfer rate.

The transfer rate can be selected from "2400," "4800," "9600," "19200," and "38400."

Note

Set the same transfer rate as those of equipment connected to each control terminal.

Control Terminal	Factory Setting
Camera	38400 bps

Switcher	19200 bps
Remote control unit	19200 bps

Alarm	38400 bps

3

I / O S P E E D

4

I/ O S P E E D

3 8 4 0 0

	UP
LEFT	RIGHT
	DOWN

R E M O T E

SET

R E M O T E

Step 6. Press the SET key to confirm the set transfer rate.

The procedure returns to Step 3, and the settings are displayed on the LCD screen.

Step 7. To further set other control terminals, repeat Steps 3 – 6.

To return to the display of the setting item, press the Clear key.

5

I/ O S P E E D

1 9 2 0 0

6

	UP
LEFT	RIGHT
	DOWN

R E M O T E

SET

29

Image 29

Contents Operating Instructions Remote ControllerTable of Contents Settings Safety Precautions Functions General DescriptionEquipment Which Can Be Controlled with the C-RM500 About the Camera Control TerminalTop Nomenclature and FunctionsDefroster key/Indicator *3 Lens speed key / Indicator *3Auxiliary contact key / Indicator *3 Auto key / Indicator *3Rear Operating the Camera OperationP E R N U a LF R O S T E R X I L I a R Y S WActivating the automatic functions T OActivating the zoom function Activating the focus functionO S I T I O N T O F O C U SChanging the lens speed Activating the auto-focus functionMonitor Display When confirming the camera number and operating its displayA N N E L C a L L Operation keysResetting individual freeze displays Simultaneously resetting all freeze displaysUsing the abbreviated numbers Using the Function keysU N C T I O N K E Y E TViewing full-screen displays H a N N E LE G M E N T Monitor screen Group E G M E N T E G S E Q Q U E N C EViewing sequential displays Sequential full-screen viewing Sequential 4-segment split-screen viewingAlarm H O L D Alarm Hold and ResetSetting Items and Their Descriptions SettingsLCD screen display Keys to be used in setting operationsOperating Keys and Display Screen S S W O R D Basic Setting OperationsE R a T I O N M O D E T O R E T U R NOperation mode Setting the FunctionsSetting contents E R a T I O N M O D E 1 . M a S T E RI T C H E R Switchers6 I N P U T M a R T Contact N T a C T E L E C T C H T O R E T U R N 1 . O N Automatic resetT O T U R N E CR a C E 2 P O S Home position selector terminal operation settingsR a C E Home positionM E R a S P E E D4 0 M O T EBuzzer I T I a L S C R E E N 1 . F U L LZ Z E R 1 . O N Initial screenChannel designation I T I a L C H a N N E LM E R a Alarm 1 . O N N S O R Alarm 1 . O NSensor alarm Camera alarmCamera check Camera alarm preset Alarm time Alarm S I G N a L 1 . E D G EAlarm signal Alarm hold Alarm F U N C T I O N 1 . S E QAlarm H O L D 1 . K E Y M 1 N C T I O N K E YM 1 5 P O S 1 2 N C T I O N K E Y a a U T O P a NAbbreviation Setting the cameras alarm contact outputM 2 2 3 P 0 S E C 0 S E CTour sequence Press the Menu key to display the menu screenCamera menu PasswordM E R a M E N U C H Example ConnectionsSystem Examples Example Connection cables Connected Camera Termination Switch SettingConnection to Combination Cameras Connection to the Multi-Switchers RS-232C Terminal Fixed camera Connection to the Smart Switchers RS-232C Terminal Shielded twisted-pair cable RS-232C reverse cable RM500 Slave Speed Switcher Connection When Controlling the System from 2 LocationsAlarm Output/Control Input Terminal Connections Assembling D-sub connectors onto cables Modifications SpecificationsAccessories 133-12-743-6E