TOA Electronics C-RM500 operating instructions I T I a L C H a N N E L, Channel designation

Page 31

6.4.9. Channel designation

Sets the first channel (camera number) to be displayed after the power is turned ON.

Note

This channel setting can only be performed when one of the settings "1. FULL," "4. 4-SEG," "5. 9-SEG," or "6. 10-SEG" has been selected in the "Initial screen" setting. The Channel Designation item is not displayed on the menu screen when another setting has been selected.

Step 1. Press the Menu key to display the menu screen.

Step 2. Tilt the joystick up or down to select "INITIAL CHANNEL," then confirm the selection with the SET key. The setting corresponding to the Initial Screen setting is displayed on Line 2.

Step 3. Using the joystick and numeric keypad, select the setting depending on the "Initial screen" setting, and confirm the selected setting with the SET key. (Refer to the table shown below.)

[Setting contents]

"Initial screen" Setting	Setting
1. FULL	Enter the channel to be designated with the numeric keypad, and confirm
(full screen)	the setting with the SET key.

			I N I T I A L C H A N N E L
			C H A N N E L				1	2 3
	Note: This selection is set to "1" by the factory.

4. 4-SEG	Tilt the joystick to the left or right to select "1 – 4," "5 – 8," "9 – 12," or "13 –
(4-segment split-screen	16" and confirm with the SET key.
display)
			I N I T I A L C H A N N E L
		1			4
		1			4
	Note: This selection is set to "1 – 4" by the factory.

5. 9-SEG	Tilt the joystick to the left or right to select "1 – 9" or "10 – 16," and confirm
(9-segment split-screen	with the SET key.
display)			I N I T I A L C H A N N E L
			I N I T I A L C H A N N E L
			1			9
			1			9

Note: This selection is set to "1 – 9" by the factory.

6. 10-SEG	Tilt the joystick to the left or right to select "1 – 8" or "9 – 16," and confirm
(10-segment split-screen	with the SET key.
display)
		I N I T I A L C H A N N E L
				8
		1
		1

Notes

•Make sure that this setting is the same as that of the connected switcher.

•This selection is set to "1 – 8" by the factory.

31

Image 31

Contents Operating Instructions Remote ControllerTable of Contents Settings Safety Precautions About the Camera Control Terminal General DescriptionFunctions Equipment Which Can Be Controlled with the C-RM500Top Nomenclature and FunctionsAuto key / Indicator *3 Lens speed key / Indicator *3Defroster key/Indicator *3 Auxiliary contact key / Indicator *3Rear Operating the Camera OperationX I L I a R Y S W N U a LP E R F R O S T E RActivating the focus function T OActivating the automatic functions Activating the zoom functionActivating the auto-focus function T O F O C U SO S I T I O N Changing the lens speedOperation keys When confirming the camera number and operating its displayMonitor Display A N N E L C a L LResetting individual freeze displays Simultaneously resetting all freeze displaysE T Using the Function keysUsing the abbreviated numbers U N C T I O N K E YE G M E N T H a N N E LViewing full-screen displays Monitor screen Group E G M E N T Sequential 4-segment split-screen viewing Q U E N C EE G S E Q Viewing sequential displays Sequential full-screen viewingAlarm H O L D Alarm Hold and ResetSetting Items and Their Descriptions SettingsOperating Keys and Display Screen Keys to be used in setting operationsLCD screen display T O R E T U R N Basic Setting OperationsS S W O R D E R a T I O N M O D EE R a T I O N M O D E 1 . M a S T E R Setting the FunctionsOperation mode Setting contentsM a R T SwitchersI T C H E R 6 I N P U TE L E C T C H N T a C TContact E C Automatic resetT O R E T U R N 1 . O N T O T U R N Home position Home position selector terminal operation settings R a C E 2 P O S R a C EM O T E S P E E DM E R a 4 0Initial screen I T I a L S C R E E N 1 . F U L LBuzzer Z Z E R 1 . O NChannel designation I T I a L C H a N N E LCamera alarm N S O R Alarm 1 . O NM E R a Alarm 1 . O N Sensor alarmCamera check Camera alarm preset Alarm signal Alarm S I G N a L 1 . E D G EAlarm time Alarm H O L D 1 . K E Y Alarm F U N C T I O N 1 . S E QAlarm hold N C T I O N K E Y a a U T O P a N N C T I O N K E YM 1 M 1 5 P O S 1 2M 2 Setting the cameras alarm contact outputAbbreviation Press the Menu key to display the menu screen 0 S E C2 3 P 0 S E C Tour sequenceM E R a M E N U C H PasswordCamera menu System Examples ConnectionsExample Example Connection to Combination Cameras Connected Camera Termination Switch SettingConnection cables Connection to the Multi-Switchers RS-232C Terminal Fixed camera Connection to the Smart Switchers RS-232C Terminal Shielded twisted-pair cable RS-232C reverse cable RM500 Slave Speed Switcher Connection When Controlling the System from 2 LocationsAlarm Output/Control Input Terminal Connections Assembling D-sub connectors onto cables Accessories SpecificationsModifications 133-12-743-6E