Sterling 882.00722.00 manual Final Connections, Display Startup Screen

Page 28

If an Ethernet module was purchased with the system, the proper setting has to be changed to measure the extruder’s RPM with communications. For details on changing the settings for measuring the extruder’s RPM, please refer to the Addendum 7-4.

The controller will be factory set to use the Ethernet module if it has been supplied.

Final Connections

Connect the rate monitor to the appropriate power source.

Connect the compressed air piping, ensuring that a 5-micron air filter is installed, along with the proper water trap. Verify that 60-psi of clean, dry compressed air is supplied to the GH Hopper.

After powering up the rate monitor, the following screen will be shown:

Figure 13: Display Startup Screen

Touch here to skip quickly to the Recipe Screen (Next Screen in sequence).

Note: It may take 45-50 seconds for the screen to appear.

This screen displays the software version of both the PLC and the Panel View. The Controller will stay on this screen for about 10 seconds or you can touch the ACS icon to quickly skip to the Recipe Screen (Next Screen in sequence). The software versions are also available on the Panel View Configuration Screen.

Figure 14: GH-M Display Main (Recipe) Screen

To access the Setup Menu to change the controller features, refer to the following pages of this manual.

Chapter 3: Installation

28 of 60

Image 28

Contents GH-M Rate Monitor Allen-Bradley Controller Write Down Your Serial Numbers Here For Future Reference Shipping Info Unpacking and InspectionEvent of Shipping Damage If the Shipment is Not CompleteReturns Warranty ReturnsCredit Returns Table of Contents Maintenance How to Use This Manual SafetySafety Symbols Used in this Manual Safety Tags and Warning Labels Description Follow all Safety Codes Wear Safety Glasses and Work GlovesGeneral Responsibility ResponsibilityOperator Responsibility Remember Maintenance Responsibility Reporting a Safety DefectAccessories Functional DescriptionModels Covered in This Manual General DescriptionCustomer Service Mechanical Features Typical Features and ComponentsController Features System Component Description Extruder Inductive Proximity SwitchSurge Hopper Open Weigh HopperFunction Typical GH-M Operator Screen Operator Screens Common to all GH Systems Typical Setup Screens Optional Components Ethernet ModulePneumatic Slide Gate below surge hopper Safety FeaturesLow Level Proximity Sensors Installation Mechanical InstallationMounting Configurations Uncrating the EquipmentElectrical Connections Machine MountPneumatic Connections Weigh Hopper Installation Initial Set-upMechanical Set-up Extruder RPM connectionFinal Connections Display Startup ScreenController Set-up GH Controller Menu Structure Recipe Page StartGH Calibration Weigh Hopper Load Cell CalibrationDisplay Calibration Menu Screen Hopper Size Setup WTP/RPM CalibrationExtruder Setup Hauloff Setup and Encoder CalibrationAlarm Setup Network SetupSetting Date and Time PanelView Configuration ScreenOperation GH-M Operation ProceduresOperator Displays GH Full Control Operation Procedures Typical Operator Screen for GH Full Control systemGH-F Gravimetric Feeder Operation Procedures Common Screens Typical Manual Control Operator ScreenAlarms with Descriptions Alarm FlagsPrint Inventory Maintenance Preventative Maintenance SchedulePreventative Maintenance Corrective MaintenanceElectrical Internal Components of the Control PanelInput Signals to Programmable Controller Output Signals from Programmable ControllerTroubleshooting IntroductionProblem Corrective action ProblemWarranty and Spare Parts Warranty SpecificationsWarranty Restrictions Warranty LiabilitiesCustomer Responsibilities Annex B InformationTypical Surge Hopper Assembly Parts List Passwords Addendum Service Supervisor InformationProgrammable Settings Typical Engineering Only Setup Screen Percent of hopper Method Default Extruder Pulse Count MethodFull Hopper Method WTP/RPM FilterMax Allowed WTP/RPM Mechanical Options ScreenDiagnostics Screen Typical Analog Options Analog options screenCustomer Setup Menu Password ProtectionAlarm Log UnitsBelow are the items that can be accessed for the GH Hopper Allen-Bradley Communications ManualAppendix Reload TOO Long Fixed Decimal Explanation Parts Department Service Department Sales DepartmentContract Department