Sterling 882.00722.00 manual Customer Responsibilities, Annex B Information

Page 48

Customer Responsibilities

Any sales, use, or other tax incident to the replacement of parts under this warranty is the responsibility of the purchaser.

Annex B Information

The following design information is provided for your reference:

1.	No modifications are allowed to this equipment that could alter the CE compliance
2.	Ambient temperature:	40 degrees Celsius – Maximum (104 degrees
	Fahrenheit)
3.	Humidity range:	50% relative humidity
4.	Altitude:	Sea level
5.	Environment:	Clean, dust-free and non-explosive
6.	Radiation:	None
7.	Vibration:	Minimal, i.e. machine mounting

8.Special installation requirements: Clean, dry compressed air 1 cfm @ 60 psi (1.7 m³/hr @ 4.14 bar)

9.	Allowable voltage fluctuation:		+/- 10%
10.	Allowable frequency fluctuation:	Continuous	+/- 1%
		Intermittent	+/- 2%

11.	Nominal supply voltage:	120/1/60 or 220/1/50/60 (Verify on serial number tag)
12.	Earth ground type:	TN (system has one point directly earthed through a
		protective conductor)

13.Power supply should include a neutral power connection.

14.Over-current protection is supplied in the GH Hopper, but additional protection should be supplied by the user.

15.The plug on the power cord serves as the electrical disconnect device.

16.Unit is not equipped with three-phase motors.

17.Functional identification

18.Cable support may be required for power cord, depending on final installation.

19.No one is required to be in the interior of the electrical enclosure during the normal operation of the unit. Only skilled electricians should be inside the enclosure for maintenance.

20.Doors can be opened with a screwdriver, but no keys are required.

21.Two-hand control is not required or provided.

22.All hoppers should be moved around and set in a place with a lift truck or equivalent.

23.There are no frequent repetitive cycles that require manual control⎯repetitive functions are automatic while the GH Hopper is operating.

24.An inspection report detailing the functional test is included with the GH Hopper.

25.The machine is not equipped with cableless controls.

26.Color-coded (harmonized) power cord is sufficient for proper installation.

Chapter 7: Appendix

48 of 60

Image 48

Contents GH-M Rate Monitor Allen-Bradley Controller Write Down Your Serial Numbers Here For Future Reference Shipping Info Unpacking and InspectionEvent of Shipping Damage If the Shipment is Not CompleteWarranty Returns ReturnsCredit Returns Table of Contents Maintenance Safety How to Use This ManualSafety Symbols Used in this Manual Safety Tags and Warning Labels Description Follow all Safety Codes Wear Safety Glasses and Work GlovesResponsibility General ResponsibilityOperator Responsibility Remember Maintenance Responsibility Reporting a Safety DefectAccessories Functional DescriptionModels Covered in This Manual General DescriptionCustomer Service Typical Features and Components Mechanical FeaturesController Features Extruder Inductive Proximity Switch System Component DescriptionSurge Hopper Open Weigh HopperFunction Typical GH-M Operator Screen Operator Screens Common to all GH Systems Typical Setup Screens Optional Components Ethernet ModuleSafety Features Pneumatic Slide Gate below surge hopperLow Level Proximity Sensors Installation Mechanical InstallationMounting Configurations Uncrating the EquipmentElectrical Connections Machine MountPneumatic Connections Weigh Hopper Installation Initial Set-upMechanical Set-up Extruder RPM connectionFinal Connections Display Startup ScreenController Set-up GH Controller Menu Structure Recipe Page StartGH Calibration Weigh Hopper Load Cell CalibrationDisplay Calibration Menu Screen Hopper Size Setup WTP/RPM CalibrationExtruder Setup Hauloff Setup and Encoder CalibrationAlarm Setup Network SetupSetting Date and Time PanelView Configuration ScreenGH-M Operation Procedures OperationOperator Displays GH Full Control Operation Procedures Typical Operator Screen for GH Full Control systemGH-F Gravimetric Feeder Operation Procedures Common Screens Typical Manual Control Operator ScreenAlarm Flags Alarms with DescriptionsPrint Inventory Maintenance Preventative Maintenance SchedulePreventative Maintenance Corrective MaintenanceElectrical Internal Components of the Control PanelInput Signals to Programmable Controller Output Signals from Programmable ControllerTroubleshooting IntroductionProblem Corrective action ProblemWarranty and Spare Parts Warranty SpecificationsWarranty Restrictions Warranty LiabilitiesCustomer Responsibilities Annex B InformationTypical Surge Hopper Assembly Parts List Addendum Service Supervisor Information PasswordsProgrammable Settings Typical Engineering Only Setup Screen Percent of hopper Method Default Extruder Pulse Count MethodFull Hopper Method WTP/RPM FilterMax Allowed WTP/RPM Mechanical Options ScreenDiagnostics Screen Typical Analog Options Analog options screenCustomer Setup Menu Password ProtectionAlarm Log UnitsBelow are the items that can be accessed for the GH Hopper Allen-Bradley Communications ManualAppendix Reload TOO Long Fixed Decimal Explanation Service Department Sales Department Parts DepartmentContract Department