Sterling 882.00722.00 manual GH Controller Menu Structure, Recipe Page Start

Page 30

“Recipe” Page (Start)

¾Extruder RPM is displayed

¾Extruder throughput is displayed

¾Line Speed is displayed (GH Full Control with Line speed option Only)

¾Weight Per Length, Weight Per Area, or simple throughput is displayed on GH Full Control versions depending on setup parameters

¾GH-F Target throughput and percent is displayed (GH-F Only)

¾Access “Inventory” Page

¾Access “Setup” Page

¾“Next” to access “Inventory” page.

GH Controller Menu Structure

“Inventory” page

¾Clear Inventory

¾Manual Control

¾“Next” returns to “Recipe” page

“Manual Control” Page

¾Reload ON/OFF

¾Return to the “Inventory” Page

“Setup” Page

¾Touch the ACS icon and enter in the “user password”

Recipe Format (for GH Full Control Only)

¾System Rate & Line Speed

¾Weigh Per Length Mode

¾Weight Per Area Mode

Hopper Setup

¾Hopper size

¾Reload Percentage

Extruder Setup

¾Maximum Extruder RPM

¾GHF Extruder Max. Throughput (GH-F Only)

Hauloff Setup (for GH Full

Control Only)

¾Hauloff enable/disable

¾Read/ Do Not read speed from COEX Master

¾Hauloff Max Speed

¾Calibrate Encoder

Calibration

¾Scale Calibration

¾Direct Scale Readout

¾Weight/RPM Calibration

Panel View Config

¾Panel view GH version

¾PLC GH version

Units

¾Lbs. vs Kgs.

Password

¾New Password

¾Verify Password

Alarm Log

¾View, print, and clear the alarm log

Alarm Setup

¾Min System Speed %

¾Max System Speed %

¾System Unstable Alarm Time

¾Maximum allowed reload time

¾Hopper % for low level alarm

¾Hopper % for no material alarm

¾Out of material alarm silence delay

Network Setup

¾IP Address

¾Subnet Mask

¾Send Config to ENI Module

¾Enable Ethernet Configurator

¾Enable or disable coexpert com

Chapter 3: Installation

30 of 60

Image 30
Contents GH-M Rate Monitor Allen-Bradley Controller Write Down Your Serial Numbers Here For Future Reference Event of Shipping Damage Shipping InfoUnpacking and Inspection If the Shipment is Not CompleteWarranty Returns ReturnsCredit Returns Table of Contents Maintenance Safety How to Use This ManualSafety Symbols Used in this Manual Safety Tags and Warning Labels Description Follow all Safety Codes Wear Safety Glasses and Work GlovesResponsibility General ResponsibilityOperator Responsibility Remember Maintenance Responsibility Reporting a Safety DefectModels Covered in This Manual AccessoriesFunctional Description General DescriptionCustomer Service Typical Features and Components Mechanical FeaturesController Features Extruder Inductive Proximity Switch System Component DescriptionSurge Hopper Open Weigh HopperFunction Typical GH-M Operator Screen Operator Screens Common to all GH Systems Typical Setup Screens Optional Components Ethernet ModuleSafety Features Pneumatic Slide Gate below surge hopperLow Level Proximity Sensors Mounting Configurations InstallationMechanical Installation Uncrating the EquipmentElectrical Connections Machine MountPneumatic Connections Mechanical Set-up Weigh Hopper InstallationInitial Set-up Extruder RPM connectionFinal Connections Display Startup ScreenController Set-up GH Controller Menu Structure Recipe Page StartGH Calibration Weigh Hopper Load Cell CalibrationDisplay Calibration Menu Screen Hopper Size Setup WTP/RPM CalibrationExtruder Setup Hauloff Setup and Encoder CalibrationAlarm Setup Network SetupSetting Date and Time PanelView Configuration ScreenGH-M Operation Procedures OperationOperator Displays GH Full Control Operation Procedures Typical Operator Screen for GH Full Control systemGH-F Gravimetric Feeder Operation Procedures Common Screens Typical Manual Control Operator ScreenAlarm Flags Alarms with DescriptionsPrint Inventory Maintenance Preventative Maintenance ScheduleElectrical Preventative MaintenanceCorrective Maintenance Internal Components of the Control PanelInput Signals to Programmable Controller Output Signals from Programmable ControllerTroubleshooting IntroductionProblem Corrective action ProblemWarranty Restrictions Warranty and Spare PartsWarranty Specifications Warranty LiabilitiesCustomer Responsibilities Annex B InformationTypical Surge Hopper Assembly Parts List Addendum Service Supervisor Information PasswordsProgrammable Settings Typical Engineering Only Setup Screen Full Hopper Method Percent of hopper Method DefaultExtruder Pulse Count Method WTP/RPM FilterMax Allowed WTP/RPM Mechanical Options ScreenDiagnostics Screen Typical Analog Options Analog options screenAlarm Log Customer Setup MenuPassword Protection UnitsBelow are the items that can be accessed for the GH Hopper Allen-Bradley Communications ManualAppendix Reload TOO Long Fixed Decimal Explanation Service Department Sales Department Parts DepartmentContract Department