Sterling 882.00722.00 Addendum Service Supervisor Information, Passwords, Programmable Settings

Page 50

7-2 Addendum (Service Supervisor Information)

Note: Untrained personnel of the rate monitor controller, should not use this section of the manual and/or program can be compromised!

Note: Hidden, programmable features and hidden menu pages should not be made available to floor operators. These pages include the Service Supervisor Information addendum located in this section. Unauthorized changes to these factory settings by inexperienced operators may prevent the unit from operating properly, and may void part or all of the warranty.

Caution! After all selections are made: Keep pressing the “Done” key until the unit returns to the Recipe menu.

Note: Inexperienced operators or inexperienced plant personnel should not access programmable features. Unauthorized changes may prevent the rate monitor from operating properly and may void part or all of the warranty.

Note: Call the Service Department for assistance or for further explanation of these or any other programmable features, which may or may not be shown in this manual.

Note: Information included in this manual is subject to change without notice.

Passwords
•	User Password	“5413”
•	Maintenance Password	“3145348”

Caution! Maintenance password should only be supplied to qualified personnel! The program can be compromised.

Programmable Settings

The rate monitor software program has been designed to allow some customizing to achieve certain desired operating parameters. The following is a listing of the selections that are “field” programmable, followed by the procedure for doing so.

Pressing the manufacturer’s icon when in the “Setup” Directory Screen menu accesses this menu.

Figure 67: Typical Operator Setup Screen

Touch this icon and enter in the Service Password to access the Engineering Only Directory

Chapter 7: Appendix

50 of 60

Image 50

Contents GH-M Rate Monitor Allen-Bradley Controller Write Down Your Serial Numbers Here For Future Reference Event of Shipping Damage Shipping InfoUnpacking and Inspection If the Shipment is Not CompleteCredit Returns Warranty ReturnsReturns Table of Contents Maintenance Safety Symbols Used in this Manual SafetyHow to Use This Manual Safety Tags and Warning Labels Description Follow all Safety Codes Wear Safety Glasses and Work GlovesOperator Responsibility ResponsibilityGeneral Responsibility Remember Maintenance Responsibility Reporting a Safety DefectModels Covered in This Manual AccessoriesFunctional Description General DescriptionCustomer Service Controller Features Typical Features and ComponentsMechanical Features Surge Hopper Extruder Inductive Proximity SwitchSystem Component Description Open Weigh HopperFunction Typical GH-M Operator Screen Operator Screens Common to all GH Systems Typical Setup Screens Optional Components Ethernet ModuleLow Level Proximity Sensors Safety FeaturesPneumatic Slide Gate below surge hopper Mounting Configurations InstallationMechanical Installation Uncrating the EquipmentElectrical Connections Machine MountPneumatic Connections Mechanical Set-up Weigh Hopper InstallationInitial Set-up Extruder RPM connectionFinal Connections Display Startup ScreenController Set-up GH Controller Menu Structure Recipe Page StartGH Calibration Weigh Hopper Load Cell CalibrationDisplay Calibration Menu Screen Hopper Size Setup WTP/RPM CalibrationExtruder Setup Hauloff Setup and Encoder CalibrationAlarm Setup Network SetupSetting Date and Time PanelView Configuration ScreenOperator Displays GH-M Operation ProceduresOperation GH Full Control Operation Procedures Typical Operator Screen for GH Full Control systemGH-F Gravimetric Feeder Operation Procedures Common Screens Typical Manual Control Operator ScreenPrint Inventory Alarm FlagsAlarms with Descriptions Maintenance Preventative Maintenance ScheduleElectrical Preventative MaintenanceCorrective Maintenance Internal Components of the Control PanelInput Signals to Programmable Controller Output Signals from Programmable ControllerTroubleshooting IntroductionProblem Corrective action ProblemWarranty Restrictions Warranty and Spare PartsWarranty Specifications Warranty LiabilitiesCustomer Responsibilities Annex B InformationTypical Surge Hopper Assembly Parts List Programmable Settings Addendum Service Supervisor InformationPasswords Typical Engineering Only Setup Screen Full Hopper Method Percent of hopper Method DefaultExtruder Pulse Count Method WTP/RPM FilterMax Allowed WTP/RPM Mechanical Options ScreenDiagnostics Screen Typical Analog Options Analog options screenAlarm Log Customer Setup MenuPassword Protection UnitsBelow are the items that can be accessed for the GH Hopper Allen-Bradley Communications ManualAppendix Reload TOO Long Fixed Decimal Explanation Contract Department Service Department Sales DepartmentParts Department