Sterling 882.00722.00 manual Typical Engineering Only Setup Screen

Page 51

Enter the long password “3145348” and press “Enter”. The factory setup section displays the “Engineering Only” screen. The screen similar to that shown below should be displayed and use the keystrokes described herein to change or toggle the parameters.

Figure 68: Typical Engineering Only Setup Screen

Go back to

Setup

Directory

Select the desired menu to advance to the screens listed below. The exit to the “Setup” screen select “Done”

Figure 69: Typical Advanced Weight Options Screen

Advanced Weight Options Screen

*Only adjust the weight filter upon request by service

*Increase the “Time to settle hopper after reload valve has shut” if the hopper needs more time to settle after reloading

*Increase “No flow timer” and decrease “No flow bits” to reduce nuisance “no flow” alarms. Set to “0” will disable this alarm.

Figure 70: Typical WTP Alogorithm Options

WTP Algorithm Options Screen

The method that is used to calculate the measured lbs/hr is entirely adjustable to fit any application. The three methods that can be used is “Extruder Pulse Count Method”, “Percent of Hopper Method”, or “Full hopper Method”. You cannot use the “Extruder Pulse Count Method” if you are writing the extruder speed through communications instead of using our inductive proximity switch.

Chapter 7: Appendix

51 of 60

Image 51

Contents GH-M Rate Monitor Allen-Bradley Controller Write Down Your Serial Numbers Here For Future Reference If the Shipment is Not Complete Shipping InfoUnpacking and Inspection Event of Shipping DamageWarranty Returns ReturnsCredit Returns Table of Contents Maintenance Safety How to Use This ManualSafety Symbols Used in this Manual Safety Tags and Warning Labels Description Wear Safety Glasses and Work Gloves Follow all Safety CodesResponsibility General ResponsibilityOperator Responsibility Remember Reporting a Safety Defect Maintenance ResponsibilityGeneral Description AccessoriesFunctional Description Models Covered in This ManualCustomer Service Typical Features and Components Mechanical FeaturesController Features Extruder Inductive Proximity Switch System Component DescriptionSurge Hopper Weigh Hopper OpenFunction Typical GH-M Operator Screen Operator Screens Common to all GH Systems Typical Setup Screens Ethernet Module Optional ComponentsSafety Features Pneumatic Slide Gate below surge hopperLow Level Proximity Sensors Uncrating the Equipment InstallationMechanical Installation Mounting ConfigurationsMachine Mount Electrical ConnectionsPneumatic Connections Extruder RPM connection Weigh Hopper InstallationInitial Set-up Mechanical Set-upDisplay Startup Screen Final ConnectionsController Set-up Recipe Page Start GH Controller Menu StructureWeigh Hopper Load Cell Calibration GH CalibrationDisplay Calibration Menu Screen WTP/RPM Calibration Hopper Size SetupHauloff Setup and Encoder Calibration Extruder SetupNetwork Setup Alarm SetupPanelView Configuration Screen Setting Date and TimeGH-M Operation Procedures OperationOperator Displays Typical Operator Screen for GH Full Control system GH Full Control Operation ProceduresGH-F Gravimetric Feeder Operation Procedures Typical Manual Control Operator Screen Common ScreensAlarm Flags Alarms with DescriptionsPrint Inventory Preventative Maintenance Schedule MaintenanceInternal Components of the Control Panel Preventative MaintenanceCorrective Maintenance ElectricalOutput Signals from Programmable Controller Input Signals to Programmable ControllerIntroduction TroubleshootingProblem Problem Corrective actionWarranty Liabilities Warranty and Spare PartsWarranty Specifications Warranty RestrictionsAnnex B Information Customer ResponsibilitiesTypical Surge Hopper Assembly Parts List Addendum Service Supervisor Information PasswordsProgrammable Settings Typical Engineering Only Setup Screen WTP/RPM Filter Percent of hopper Method DefaultExtruder Pulse Count Method Full Hopper MethodMechanical Options Screen Max Allowed WTP/RPMTypical Analog Options Analog options screen Diagnostics ScreenUnits Customer Setup MenuPassword Protection Alarm LogAllen-Bradley Communications Manual Below are the items that can be accessed for the GH HopperAppendix Reload TOO Long Fixed Decimal Explanation Service Department Sales Department Parts DepartmentContract Department